McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    10 Products

    Sprockets

    Image of Product. Plain Bore. Front orientation. Drive Sprockets. Sprockets, For Single Strand, Plain Bore.

    Plain Bore

    Sprocket teeth mesh with your roller chain to smoothly transmit power. These U.S.-made sprockets have machined teeth for a more precise fit than flame-cut or punched teeth, allowing them to glide in and out of the chain to reduce wear and extend chain life.
    Steel—Steel is strong, but best for dry environments since moisture will cause it to rust.
    Plain Bore—Plain bore sprockets give you options—machine a custom bore, weld, or press-fit them in place. They're sized to the minimum shaft diameter listed and are machinable up to the maximum.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    OD,
    mm
    Bore
    Type
    For Shaft
    Dia.
    Each
    For Single Strand
     
    Steel
    08BISO1/2"40169Plain19 mm to 60 mm2302K2310000000
    10BISO5/8"28151Plain19 mm to 51 mm2302K271000000
     

    Taper-Lock Bushings

    Image of ProductInUse. Front orientation. Pulley and Sprocket Bushings. Taper-Lock Bushings.
    Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing trade number. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
    Keyway,
    mm
    For Shaft
    Dia., mm
    Overall
    Wd., mm
    Wd.
    Dp.
    Taper
    Fastener Tightening
    Torque, in·lbf
    Includes
    Each
    Steel
     
    Bushing Trade Number 1008
    192262.88°55Set Screws57095K425000000
     
    Bushing Trade Number 1108
    192262.88°55Set Screws57095K43700000
     
    Bushing Trade Number 1610
    192562.88°175Set Screws57095K49300000
     

    Split-Tapered Bushings

    Image of Product. Front orientation. Contains Annotated. Pulley and Sprocket Bushings. Split-Tapered Bushings, Steel.

    Steel

    The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing trade number. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
    Keyway,
    mm
    For Shaft
    Dia., mm
    Overall
    Wd.
    Wd.
    Dp.
    Taper
    Fastener Tightening
    Torque, in·lbf
    Each
    Steel
     
    Bushing Trade Number H with Clamping Screws
    191 1/4"633°959859T717000000
     

    Flanged Screw-Clamp Bushings

    Image of Product. Front orientation. Pulley and Sprocket Bushings. Flanged Screw-Clamp Bushings.
    Image of Attribute. Side1 orientation. Contains Annotated. Flanged Screw-Clamp Bushings.
    A mounting flange prevents movement during tightening. These bushings are good for shock loads. When you tighten the included screws, the bushing's inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear. They can be mounted on shafts with or without keyways.
    For Shaft
    Dia., mm
    OD,
    mm
    Overall
    Wd., mm
    Max. Torque,
    in·lbf
    Fastener Tightening
    Torque, in·lbf
    Includes
    Each
    Steel
    1933241,05042Clamping Screws1058K73000000
     

    Corrosion-Resistant Flanged Screw-Clamp Bushings

    Image of Product. Back orientation. Pulley and Sprocket Bushings. Corrosion-Resistant Flanged Screw-Clamp Bushings.
    Image of Attribute. Side1 orientation. Contains Annotated. Corrosion-Resistant Flanged Screw-Clamp Bushings.
    Made from stainless steel or plated with nickel, these bushings resist corrosion. A mounting flange prevents movement during tightening. As screw-clamp bushings, they're good for shock loads. When you tighten the clamping screws, the bushing's inner sleeve tightens onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear.
    Nickel-Plated Steel—Nickel-plated steel bushings have good corrosion resistance in wet environments. However, the plating may begin to flake with long-term use.
    Stainless Steel—Stainless steel bushings have excellent corrosion resistance and can withstand prolonged exposure to moisture.
    For Shaft
    Dia., mm
    OD,
    mm
    Overall
    Wd., mm
    Max. Torque,
    in·lbf
    Fastener Tightening
    Torque, in·lbf
    Includes
    Each
    Nickel-Plated Steel
    1944341,05070Clamping Screws5530N220000000
     
    Stainless Steel
    19443485060Clamping Screws5530N107000000
     

    Quick-Grip Screw-Clamp Bushings

    Image of Product. Front orientation. Pulley and Sprocket Bushings. Quick-Grip Screw-Clamp Bushings.
    Also known as Trantorque bushings, these tighten with a twist of the collar nut—no screws needed. As you tighten the collar nut, the inner sleeve contracts onto the shaft and the outer sleeve expands to hold your sprocket, pulley, or gear.
    For Shaft
    Dia., mm
    OD,
    mm
    Overall
    Wd., mm
    Max. Torque,
    in·lbf
    Each
    Steel
    1932292,1502298K660000000
     
    back to top