McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Roller Chain Trade Number
    Pitch
    Attribute Image
    Number of Teeth
    Strand Type
    Bore Type
    Chain Type
    Material
    Bushing Trade Number
    Chain Standard
    Hub Diameter
    Shaft Type
    Sprocket Type
    Keyway Width
    Attribute Image
    Shaft Mount Type
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Industrial Info Compare
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Keyway Depth
    Attribute Image
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    8 Products

    Sprockets

    Image of Product. Plain Bore. Front orientation. Drive Sprockets. Sprockets, For Single Strand, Plain Bore.

    Plain Bore

    Image of Product. Front orientation. Drive Sprockets. Sprockets, For Double Strand.

    For Double Strand

    Sprocket teeth mesh with your roller chain to smoothly transmit power. These U.S.-made sprockets have machined teeth for a more precise fit than flame-cut or punched teeth, allowing them to glide in and out of the chain to reduce wear and extend chain life.
    Steel—Steel is strong, but best for dry environments since moisture will cause it to rust.
    Wear-Resistant Steel with Hardened Teeth—These sprockets have teeth that are hardened from the tip to the base so they withstand chain contact and wear evenly. That means fewer broken teeth and a longer lifespan than sprockets with unhardened or tip-hardened teeth. Steel is best for dry environments since moisture will cause it to rust.
    Plain Bore—Plain bore sprockets give you options—machine a custom bore, weld, or press-fit them in place. They're sized to the minimum shaft diameter listed and are machinable up to the maximum.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    OD
    Bore
    Type
    For Shaft Dia.
    Each
    For Single Strand
     
    Steel
    160ANSI2"96 11/16"Plain
    		1 1/2" to 2 1/8"6793K4110000000
     
    For Double Strand
     
    Wear-Resistant Steel with Hardened Teeth
    50-2ANSI5/8"194 1/8"Plain
    		1" to 2 1/8"2784K42000000
     

    Taper-Lock Bushings

    Image of ProductInUse. Front orientation. Pulley and Sprocket Bushings. Taper-Lock Bushings.
    Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing trade number. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
    Keyway
    For Shaft
    Dia.
    Overall
    Wd.
    Wd.
    Dp.
    Taper
    Fastener Tightening
    Torque, in·lbf
    Includes
    Each
    Steel
     
    Bushing Trade Number 2012
    2 1/8"1 1/4"1/2"3/16"8°280Machine Key, Set Screws57095K1960000000
     
    Bushing Trade Number 2517
    2 1/8"1 3/4"1/2"1/4"8°430Set Screws57095K21700000
     
    Bushing Trade Number 3020
    2 1/8"2"1/2"1/4"8°800Set Screws57095K337000000
     

    Quick-Disconnect (QD) Bushings

    Image of Product. Front orientation. Pulley and Sprocket Bushings. Quick-Disconnect (QD) Bushings, Clamp-On Shaft Mount.
    Image of Attribute. Side1 orientation. Contains Annotated. Quick-Disconnect (QD) Bushings.

    Clamp-On Shaft Mount

    The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing trade number. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
    Keyway
    Overall
    Wd.
    Wd.
    Dp.
    Fastener Tightening
    Torque, in·lbf
    Material
    Includes
    For Shaft
    Dia.
    Each
    Clamp-On Shaft Mount
     
    Bushing Trade Number SF
    2 1/16"1/2"1/4"360Sintered SteelClamping Screws2 1/8"6086K635000000
     
    Bushing Trade Number SK
    1 15/16"1/2"1/4"180Sintered SteelClamping Screws2 1/8"6086K53200000
     

    Hub-Mount Screw-Clamp Bushings

    Image of Product. Front orientation. Pulley and Sprocket Bushings. Hub-Mount Screw-Clamp Bushings.
    Image of Attribute. Side1 orientation. Hub-Mount Screw-Clamp Bushings.

    Transfer torque directly from a shaft to a hub. These bushings install over your hub to mount a sprocket, pulley, or gear to a shaft at the same time. Common in industrial gearbox applications, they can also connect a hollow shaft over a solid shaft. As screw-clamp bushings, they're good for shock loads. When you tighten the included clamping screws, the outer rings compress against a sprocket, pulley, or gear in between them, causing the inner rings to tighten around the shaft.
    For Shaft
    Dia.
    OD
    Overall
    Wd.
    Max. Torque,
    in·lbf
    Fastener Tightening
    Torque, in·lbf
    Each
    Zinc-Plated Steel
    2 1/8"3 15/16"1 5/16"12,1501007654N160000000
     
    back to top