Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

Install these low-profile valves in tight spots. Use with water, oil, air, and inert gas.

With 10-32 UNF threads and a body less than 3/4” long, these valves are often used to control flow in miniature pipelines. They’re rated for use with water, oil, air, and inert gas.

Open and close these valves with the flip of the toggle switch. They’re often used for equipment testing and gas sampling. All have threads and a hex nut below the handle for installation in instrument panels. Use with water, oil, air, and inert gas.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components. Use with water, oil, air, inert gas, and steam.

Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, inert gas, and steam.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Bolt these valves to ANSI flanges. They’re for use with water, oil, air, inert gas, and steam.

For a leak-tight connection that doesn’t require heat or soldering, these valves have press-connect fittings that crimp to metal tubing with a press-connect crimping tool.

Often used for oxygen service and other high-purity applications, these valves come cleaned and bagged. Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. For easy maintenance, they have a three-piece bolted body that disassembles inline so you can access internal components without removing welded connections.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

To withstand aggressive and corrosive solutions in miniature chemical-processing pipelines, these tiny valves have a chemical-resistant fluoroelastomer seal and a corrosion-resistant 303 stainless steel body.

Attach gauges or sensors to these valves so you can remove them for maintenance and calibration without depressurizing your line. They are also known as block and bleed valves.

To maintain sanitary standards in food, beverage, and dairy systems that require frequent cleaning, these valves are made of FDA compliant materials. Electropolished to a 32 Ra finish, they have smooth internal surfaces that prevent product buildup and inhibit bacteria growth. All have sanitary quick-clamp fittings for easy disassembly.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. They have polished internal surfaces for easy cleaning in food and beverage systems.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use with diesel fuel, fuel oil, gasoline, and kerosene.

To create a tight seal in vacuum conditions higher than 29.9” Hg, these valves have ultra-high-vacuum tube fitting connections, which are also known as KF, QF, and NW fittings. They are often used in applications such as vacuum coating and heat treating, leak testing, and analyzing gases.

Also known as vacuum isolation valves, these block flow so you can install and remove gauges from your system. They can also be used to add or vent gases in high-vacuum systems.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

Designed to withstand the high temperatures and pressures in steam service applications.

Use with coolant and detergent such as ethylene glycol or soap solutions.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

Their ball-valve design allows these valves to handle three times the flow of butterfly valves.

With a ball-valve design, these valves can handle three times the flow of butterfly valves.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Their ball valve design allows these valves to handle three times the flow of butterfly valves.

For food and beverage systems that require frequent cleaning, these valves have polished internal surfaces and sanitary quick-clamp connections for easy disassembly.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Designed to withstand the extreme cold of liquid argon, liquid carbon dioxide, and liquid nitrogen, these valves are cleaned and bagged to meet CGA G-4.1 standards for oxygen service. They gradually open and close to adjust and regulate flow.

For a longer service life than other flanged flow-adjustment valves, these are designed to open and close with minimal wear on internal components. Use with water, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a low-profile body and a narrow port-to-port length, these valves fit in tight spots. Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often used in sterilization applications with clean steam, these valves are electropolished to a 16 Ra finish for smooth internal surfaces that prevent product buildup and inhibit bacteria growth.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Used in food, beverage, and dairy systems that require frequent cleaning, these valves are FDA compliant for direct food contact. Electropolished to a 20 Ra finish, they have smooth internal surfaces that prevent product buildup and inhibit bacteria growth. All have sanitary quick-clamp fittings for easy disassembly. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For faster actuation than motor-driven valves, these operate on compressed air. Integrate them into PLC systems for automatic control over the valve position based on system conditions. The actuator has a built-in electric pilot valve that controls the air supply to the valve. Set how much to open the valve using the programmable controller on the actuator.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

Designed to direct the flow of liquids in food, dairy, and chemical-processing facilities, these valves can be fully disassembled for clean-out-of-place (COP) processes.

Often installed on petroleum loading arms to test fuel quality without interrupting flow, these valves are fire-tested to meet American Petroleum Institute (API) 607, Edition 5, for securely isolating fluid and preventing the spread of fire.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

For food and beverage systems that require frequent cleaning, these valves have sanitary quick-clamp connections for easy disassembly. They operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

With a shorter end-to-end length than other check valves, these fit in tight spaces.

Plastic provides a lightweight alternative to metal.

The heat-resistant rubber seal withstands temperatures up to 500° F.

For more durability than plastic barbed check valves, these have a stainless steel body.

Less than half the end-to-end length of standard flange-mount check valves, these can be installed in pipelines with limited clearance.

Weld to unthreaded metal pipe.

To reduce installation time and allow for maintenance without detaching pipe connections, these valves insert into a union fitting.

Barbs grip onto tubing, providing a secure hold.

These heavy duty valves can withstand pressures up to 1,975 psi and temperatures up to 800° F.

Rated for at least four times the pressure of standard check valves for oil and fuel, these are often used in hydraulic applications with pressures up to 3,000 psi.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection.

These compact valves fit into standard sanitary quick-clamp fittings. All are FDA Compliant 21 CFR 177.2600 and have polished surfaces for easy cleaning.

To withstand high pressures and temperatures in steam service applications, these valves have a 316 stainless steel body, PTFE ball, and PTFE seal.

Rated for 12 times the pressure of standard vacuum-breaking valves, these can handle up to 1,500 psi. Connections are NPT.

Attach these balancing valves using solder—they help you measure the difference in pressure across the valve and adjust the flow rate to system components. Also known as circuit setters, they’re often used in systems that need an even distribution of flow, such as HVAC systems.

Compression fittings bite down on the outside of hard metal tubing for a secure connection.

Press these orifices into machined holes in connectors, manifolds, and other custom parts.

Also known as flow restrictors and precision orifice valves, these orifices are used to throttle, vent, bleed, or regulate flow in water systems.

Smaller than other float valves, these are sized for containers with limited space.

Commonly used in ice-making machines, these valves have floats that rest inside a clear plastic reservoir.

Automatically remove condensate from compressed air or inert gas lines—these float valves have a float-operated drain control.

Connect float valve bodies and floats with these rods.

Mount these valves directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

These valves open to allow flow in one direction and close when flow stops or reverses direction.

A 316 stainless steel housing allows these regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.

These withstand at least double the pressure of our other timer-operated drain valves.

Add air and hydraulic fluid to high-pressure struts, tanks, and hydraulic accumulators—these fill valves withstand pressures up to 5,000 psi.

To minimize fluid loss when connecting and disconnecting your line, these couplings have flat faces for a close fit and shut-off valves to stop the flow—they meet ISO 16028, which is an international standard for hose couplings.

Designed for ultra-clean environments, these manifolds are cleaned, dried, and vacuum sealed in plastic to prevent dirt and moisture from contaminating the inside. Use them to distribute air or fluid to multiple locations from a single supply source. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Mount these manifolds on the end of a hose line to distribute air, water, or hydraulic fluid to three locations from a single supply source.