Secure ceiling tiles or join ceiling tile frame components.

Clips for ceiling tiles keep ceiling tiles in place. Those for 1/16"-5/8" ceiling tiles are best for entryways and other drafty areas.

Clips for ceiling tile frames join ceiling tile frames and molding. Cross clips connect cross tees to main beams. For those with a 1” notch depth, use cross-lock clips to secure them in place. Both clips help you comply with ICC-ES seismic requirements when fastened with pop rivets. Use cross clips with a 1 9/32” notch depth to install lights or vents to beams where there isn’t a notch. Straight clips attach two main beams. When installed with pop rivets, these clips help you meet ICC-ES seismic standards. Tee clips join molding to main beams and cross tees. Those for 9/16”-15/16” ceiling tile frames help you comply with ICC-ES seismic requirements when properly installed.

PVC plastic clips must be used with fiberglass-reinforced plastic ceiling tile frames and molding.

Instead of painting or replacing ceiling tile frames when they’re rusted and discolored, put these flexible PVC covers onto them for a clean appearance. They’re sized to fit most framing systems. If you’re using them with ceiling tiles with recessed edges, make sure the width of the covers will fit the recess.

Rated ASTM E84 Class A, their ability to limit the spread of flames and generation of smoke conforms to the highest classification. They also meet UL 94 V-0, which means they’ll self-extinguish within 10 seconds and won’t spread fire by dripping.

To cover your framing’s perimeter, use wall covers. They slide onto framing where the ceiling and wall meet.

To cover your framing’s interior grid, you may need both standard and tee covers. Standard covers have a notch in the middle that covers the seams where two tee covers meet. They’re compatible with both 2' × 2' and 2' × 4' ceiling tiles. When used with 2' × 4' tiles, install them on the 2' side. Tee covers run perpendicular to standard covers to create a tee.

For a proper fit, choose covers for 1" wd. framing if your current 15/16" wd. framing already has a thick coating of paint.

For technical drawings and 3-D models, click on a part number.

Drill a hole into concrete or other hard surfaces, and hammer in these hangers. Once the hanger is inserted, pulling on the head with the claw of a hammer will cause the base to expand, wedging the hanger in place. They’re zinc plated for corrosion resistance in wet environments.

For technical drawings and 3-D models, click on a part number.

Also known as spade bolts, you can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt). Zinc plating provides corrosion resistance in wet environments. Material meets ASTM A307 or F2282 specifications for quality.

For technical drawings and 3-D models, click on a part number.

Drill holes with the point on these hangers. Install with a special driver bit (sold separately).

Zinc-yellow-chromate-plated hangers are corrosion resistant in wet environments. Zinc-yellow-chromate-plated hangers with a 3/8" head width can drill through steel sheet metal as thick as 16 ga. Some hangers with a 7/16" head width can drill through steel as thick as 12 ga.; others can drill through sheet metal and wood.

Corrosion-resistant-coated hangers are 40 times as corrosion resistant as zinc-yellow-chromate-plated hangers, withstanding up to 1,000 hours of salt spray. They can drill into structural steel up to 1/4", such as steel beams. They’re not for use with sheet metal thinner than 12 ga.

For technical drawings and 3-D models, click on a part number.

Drive these hangers into wood with an adjustable wrench, pliers, or a special driver bit (sold separately). They’re also known as eye lags.

Zinc- and zinc yellow-chromate plated steel hangers are corrosion resistant in wet environments. The zinc yellow-chromate plated steel hangers meet quality standards outlined in ASTM B633 and dimensional standards outlined in ASME B18.2.1.

316 stainless steel hangers have excellent resistance to chemicals and salt water. They’re best for corrosive and marine environments.

For technical drawings and 3-D models, click on a part number.

These hangers are a popular choice for overhead applications. To install, insert the bolt through your fixture and thread the toggle onto it. Next, fold the toggle wings flush against the bolt and push them through a drilled hole until they pop open on the other side. Pull back on the bolt and tighten. They’re zinc plated for corrosion resistance in wet environments. Dimensions meet ASME B18.6.3 specifications.

For technical drawings and 3-D models, click on a part number.

These hangers are a popular choice for overhead applications. The spring holds the washer and toggle against opposite sides of the wall, so everything's in position before you begin tightening. To install, insert the bolt through your fixture and thread the toggle onto it. Next, fold the toggle wings flush against the bolt and push them through a drilled hole until they pop open on the other side. Once tightened, the spring adds vibration resistance. Zinc yellow-chromate plating provides corrosion resistance in wet environments. Dimensions meet ASME B18.6.3 specifications.

For technical drawings and 3-D models, click on a part number.

Attach these light duty hangers to ceilings and walls. They have a stiff wire for supporting suspended ceilings, lighting fixtures, and other lightweight material.

Threaded hangers have a pointed screw end for tapping into wood.

Screw-on hangers have an unthreaded hole for mounting with a fastener.

For technical drawings and 3-D models, click on a part number.