Rated NEMA 3R, these rain-tight switches protect against falling liquids and light splashing. More precise than other time and day switches, they program on/off times for equipment down to the exact minute. They control equipment with high currents, such as landscape lighting, pumps, and heaters. A backup battery maintains the program during a power outage.

24-hour switches repeat the same program daily.

Seven-day switches can perform a different program each day of the week.

Switches with a day skipper can be programmed to skip operation for one to six days.

For precise control of high-current equipment such as landscape lighting, pumps, and heaters, these switches schedule on/off times to the exact minute. A backup battery or capacitor maintains the program during a power outage.

Seven-day switches can perform a different program each day of the week. They have a day skipper that can suspend operation for one to six days.

Two-circuit switches can apply a different program to each circuit.

Protected by a steel enclosure, these switches withstand tougher conditions than switches in a plastic housing. Also known as safety switches, they have quick-make/quick-break action to eliminate arcing and prolong switch life. They have a lockout to secure in the off position using a padlock (not included).

Use switches with a fuse holder where overload protection is needed. When used with UL Class RK1, RK5, or T fuses, they require rejection-style fuse clips. Note: Horsepower ratings are based on time-delay fuses installed.

Switches with safety interlock keep the door closed when the switch is on, and prevent the switch from turning on when the door is open.

For technical drawings and 3-D models, click on a part number.

A raintight NEMA 3R rated enclosure protects these switches from falling liquids and light splashing. The enclosure is steel, so it withstands tougher conditions than plastic enclosures. All have quick-make/quick-break action to eliminate arcing and prolong switch life. They have a lockout to secure in the off position using a padlock (not included).

Use switches with a fuse holder where overload protection is needed. When used with UL Class RK1, RK5, or T fuses, they require rejection-style fuse clips. Note: Horsepower ratings are based on time-delay fuses installed.

Switches with safety interlock keep the door closed when the switch is on, and prevent the switch from turning on when the door is open.

For technical drawings and 3-D models, click on a part number.

Cut power and keep it isolated to prevent equipment from starting up during inspection and maintenance. These switches are housed in a protective enclosure.

Switches with lockout secure in the off position with a padlock with a maximum shackle diameter of 5/16” (not included).

Use additional power poles to control more than three circuits. Add neutral poles to open and close the neutral leg of a three phase system.

For technical drawings and 3-D models, click on a part number.

Turn heating equipment on or off at a specified temperature. Switches have a probe on a cable for remote temperature readings. Set the actuation point with the adjustment dial.

Switches that control two circuits are double pole, single throw (DPST). They turn two circuits from on to off (normally closed).

Switches with an open housing are often added to existing enclosures or custom installations.

Switches with a pilot light indicate when the switch is on.

Use packing seals and fittings (sold separately) to seal the probe into threaded tanks and pipes.

To protect these switches from splashing water, corrosive liquid, and dust, the housing meets NEMA 4X for washdown conditions. Switches turn heating equipment on or off at a specified temperature. All have a probe on a cable for remote temperature readings. Set actuation points with the adjustment dial.

DPST (Double pole, single throw) switch turns two circuits from on to off (normally closed).

Regulate line-voltage HVAC systems.

Thermostats for heaters mount to a surface-mount outlet box.

A built-in guard prevents accidental changes and other tampering and protects these thermostats from damage. These thermostats regulate the temperature in HVAC systems that use direct electrical power. They’re often used with baseboard and wall heaters.

DPST (double pole, single throw) thermostats control two circuits, so they have an “off” setting that cuts power to the thermostat. As a result, they’re more energy efficient and slightly safer than SPST (single pole, single throw) thermostats, which stay at a low setting instead of turning off completely.

For technical drawings and 3-D models, click on a part number.