Keep equipment level on slightly sloped and pitted floors with mounts that have a ball-and-socket joint in the base. Add your own stud to create a custom-length mount that you can install in either threaded holes or unthreaded through holes.

Keep equipment level on slightly sloped and pitted floors with mounts that have a ball-and-socket joint in the base. For mounting versatility, you can install them in either threaded holes or unthreaded through holes at the bottom of equipment.

Remove the shackle after lifting while keeping the base installed for future use. Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque Wrenches are sold separately.

Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.

Warning: Never use to lift people or items over people.

The ball bearing on these hoist rings makes it easy to rotate your load even after it’s suspended. For unbalanced or heavy loads, the base also swivels to compensate for pitch, roll, and sway. Their lifting ring pivots 180° front to back. Ideal for angular lifting, these hoist rings withstand stresses that bend or break eyebolts.

Install the base of these hoist rings flush to your mounting surface. Use a torque wrench to tighten to the recommended torque stamped on the ring.

Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.

Warning: Never use to lift people or items over people.

A rubber cushion reduces vibration to protect components and extend your machine’s life. These mounts have a ball-and-socket joint in the base that swivels to compensate for slightly sloped and pitted floors. Add your own stud to create a custom-length mount that you can install in either threaded holes or unthreaded through holes.

These rod end bolts are good for wet and corrosive environments—for maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

For maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

These alloy steel rod end bolts have the highest tensile strength of any steel fully threaded rod end bolt we offer. For maximum mounting flexibility, cut the fully threaded shaft to whatever length you need. Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

Create pivoting connections in applications that require high shear strength—the partially threaded shank of these rod end bolts withstands more side force than a fully threaded shank. Also known as swing bolts and eyebolts, they are used to create hinges, turnbuckles, and tie downs. Unlike ball joint rod ends, these rod end bolts are made from a single piece of metal, so they wear down more slowly and have a more controlled swing. However, because they do not have a moving ball joint, they do not compensate for angular misalignment. Made from steel, they are stronger and more wear resistant than stainless steel rod end bolts, but they are not as corrosion resistant.

A rubber cushion reduces vibration to protect components and extend your machine’s life. For mounting versatility, you can install them in either threaded holes or unthreaded through holes at the bottom of equipment.