McMaster-Carr logo
    Filter by
    Number of Terminals per Circuit
    Color
    Mounting Location
    Wire Connection
    Number of Circuits
    Attribute Image
    System of Measurement
    Width
    Attribute Image
    Electrical Connection
    DIN Rail Height
    DIN Rail Trade Size
    Grounding
    Current per Circuit
    For Wire Gauge
    Industrial Info Compare
    Length
    Attribute Image
    Height
    Attribute Image
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Flammability Rating
    Manufacturer
    Maximum Temperature
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Industrial Info Snippet
    Wire Entry Location
    Manufacturer Model Number
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    8 Products

    Quick-Connect Modular DIN-Rail Mount Terminal Blocks

    Image of System. Front orientation. Contains Annotated. Terminal Blocks. Quick-Connect Modular DIN-Rail Mount Terminal Blocks.
    Pop wire in and out of these terminal blocks without adjusting a screw for faster installation. Once clamped in place, the wire will stay put when vibrated, bent, or pulled.
    Mix and match these terminal blocks to get the exact number of circuits you need in a single setup. Add blocks for thermocouples, fuses, and grounding wire as needed. The blocks clip side by side onto DIN rail in control panels, creating tidy rows of circuits that you can identify and access on the spot.
    Terminal Blocks with Spring-Clamp Terminals
    Image of Product. Front orientation. Terminal Blocks. Quick-Connect Modular DIN-Rail Mount Terminal Blocks, Terminal Blocks with Spring-Clamp Terminals.
    Faster to install than screw terminals. Lift the clamp with a screwdriver, then release the clamp down onto the inserted wire.
    Covers—Snap onto the exposed side of a terminal block to prevent accidental contact with a live wire.
    End Stops—Mount at the end of a group of terminal blocks so they don't slide when vibrated or bumped.
    Adjacent Jumpers—Metal poles create an electrical connection between adjacent terminal blocks, so you can connect multiple components with a single wire. Blocks must be the same width for the jumpers to fit.
    Alternate Jumpers—Connect terminals on two blocks of the same width, skipping a block in between. This reduces wire clutter and gives you flexibility to adjust your set-up in the future.
    Terminal Blocks
    Covers
    End Stops
    Adjacent Jumpers
    Alternate Jumpers
    Each
    No. of
    Circuits
    No. of Terminals
    per Circuit
    For Wire
    Ga.
    Wd.,
    mm
    Ht.,
    mm
    For DIN Rail
    Trade Size
    Color
    1-24
    25-Up
    Each
    Each
    Insulation
    Each
    Insulation
    Each
     
    600V AC/600V DC—15 amp per Circuit
    1422 to 144.2703Blue9473T18200000000009473T195000009473T14400000Insulated9473T19300000Insulated9473T19400000
     
    Markers
    Image of Product. Front orientation. Terminal Block Markers. Blank.
    Image of Product. Front orientation. Terminal Block Markers. Numbered for Horizontal Rails.
    Image of Product. Front orientation. Terminal Block Markers. Numbered for Vertical Rails.

    Blank

    Numbered

    for

    Horizontal

    Rails

    Numbered

    for

    Vertical

    Rails

    Label your terminal block connections so you can identify them at a glance.
    Each
    For Terminal
    Block Wd., mm
    Number
    Range
    Includes
    Markers
    per Card
    Color
    1-24
    25-Up
    Blank
    4.2——100White9473T2170000000000
     
    Numbered for Horizontal Rails
    4.21 to 50Two of Each Number100White9473T218000000000
     
    Numbered for Vertical Rails
    4.21 to 50Two of Each Number100White9473T2190000000000
     
    back to top