These Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Grade B16 threaded rods maintain their strength at higher temperatures than Grade B7 threaded rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Stronger and more wear resistant than 18-8 stainless steel, these threaded rods are mildly chemical resistant. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

The most corrosion resistant stainless steel threaded rods we offer, these Alloy 20 stainless steel threaded rods contain nickel to withstand exposure to sulfuric, phosphoric, and nitric acids.

Unlike metal rods, these threaded rods will not warp at extreme temperatures, making them ideal for heat treating and furnace fixtures.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

One-third the weight of steel, aluminum threaded rods resist corrosion in wet environments.

Bronze threaded rods are stronger and more resistant to salt water than brass rods.

Commonly used in valves, pumps, and shafts, these 400 nickel threaded rods resist salt water and caustic chemicals.

Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.

18-8 stainless steel studs have good chemical resistance.

These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.

These studs have good chemical resistance. Weld them to stainless steel surfaces.

316 stainless steel studs have excellent resistance to chemicals and salt water.

A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring.

Made from Grade 5 steel, these inch-sized coupling nuts are suitable for most applications.

Comparable in strength to Grade 9 bolts, these coupling nuts are about 20% stronger than high-strength steel coupling nuts. Available in inch thread sizes.

More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.

Plastic coupling nuts are chemical resistant, nonconductive, and lightweight.

Stainless steel coupling nuts have excellent corrosion resistance in most environments.

A smooth rounded body provides a finished look.

Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure. They have a flat surface area that allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

Clip retaining rings into the grooves to separate and position gears, sprockets, and bearings.