Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

Mount along a wall or other vertical surface.

Use these carriages and guide rails for light loads where precise movement is not required.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

These steel track rollers and guide rails support loads up to 300 lbs.

A handle on the side of the carriage locks the carriage in place.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

A handle locks these carriages in place on curved paths, loops, and circuits in assembly stations and other repetitive processes.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Designed for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Slides have a row of ball bearings on each side of the rail.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

These slides fully extend for convenient access to the back of drawers.

The stacked design provides stability for deep and wide drawers.

These slides provide full extension for convenient access to the back of your drawers.

With fewer moving parts than other lock-open drawer slides, these collect less debris for a longer service life.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

A stop holds the drawer open; push firmly on the drawer to close.

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.

A stop holds the drawer closed; pull firmly on the drawer to open.

With no external moving parts, these air slides provide a long stroke, but have a static footprint—only the carriage on top moves.