Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Use for pressures up to 200 psi. Also known as insert fittings, these slide into semi-flexible plastic pipe and secure with a clamp.

Connect these fittings to UV-resistant PVC pipe. Designed for outdoor use, they contain an additive that protects against the damaging effects of ultraviolet light. Fittings are typically used in low-pressure residential and commercial plumbing and water supply applications up to 300 psi.

Bolt two same-size flanges together with a gasket to create an access point within a line. Flanges are an economical option for gravity-flow chemical waste systems. They are ABS plastic, which has excellent strength and impact resistance and good chemical resistance.

Use these clamps to connect easy-access CPVC pipe fittings and pipe.

These fittings have excellent corrosion resistance to handle a wide range of acids and other highly-corrosive chemicals. They are commonly used in metal surface treating applications, plating solution lines, and other chemical process applications. Reinforced with layers of fiberglass, they have better strength and durability than any of our other pipe fittings for chemicals.

These Schedule 40 fittings are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

Crimp these fittings onto steel pipe to form a tightly sealed connection that’s faster than threading or welding and doesn’t require heat.

These junction blocks have threaded holes that allow air or fluid to flow at a 90° angle through the block. Use them to organize and separate multiple lines in your system.

The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

A PTFE seal on the tube end of these fittings allows for an extra-strong connection in high-vibration applications.

Solder these fittings to tubing for a permanent, leak-tight connection. They are also known as sweat fittings.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Made of plastic, these fittings are lightweight compared to our brass push-to-connect fittings.

Also known as instrumentation fittings, these are made to tighter tolerances than standard compression fittings. They are compatible with Parker CPI fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Monitor flow with these clear fittings.

Color-code fittings for easy identification. These aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

Aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

Made of stainless steel, these fittings have better corrosion resistance than brass fittings.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

A built-in tube support slips inside the tubing to prevent collapsing and provides a sturdy connection for an extra-tight seal.

Made of FDA listed materials, these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Made of stainless steel, these fittings are more durable than plastic barbed tube fittings for food and beverage.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Fittings have a barb that grips onto tubing. Use in applications up to 120 psi.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push, and an internal gripping ring and fluoroelastomer O-ring hold the tubing tight.

Fittings have a barb that grips onto tubing. Use in applications up to 150 psi.