Use these valves in general purpose applications such as those with water, oil, air, and inert gas.

For applications that require intermittent operation, such as spraying and washing, push or pull the lever on these valves to start flow. They spring closed when the lever is released.

For installation through thick insulation, these valves have an extra-long stem. They’re for use with water, oil, air, inert gas, and steam.

Install these low-profile valves in tight spots. Use with water, oil, air, and inert gas.

With 10-32 UNF threads and a body less than 3/4” long, these valves are often used to control flow in miniature pipelines. They’re rated for use with water, oil, air, and inert gas.

Open and close these valves with the flip of the toggle switch. They’re often used for equipment testing and gas sampling. All have threads and a hex nut below the handle for installation in instrument panels. Use with water, oil, air, and inert gas.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components. Use with water, oil, air, inert gas, and steam.

Often used in high-purity applications, such as oxygen service, these valves come cleaned and bagged. Use with water, oil, inert gas, and steam.

Use these valves with garden hose and other landscaping equipment. They’re for use with water, air, and inert gas.

Install these low-profile valves in tight spots. They are for use with water, oil, air, and inert gas.

Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, inert gas, and steam.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Metal provides more durability than plastic. These valves have barbed fittings that grip onto tubing for a secure hold. Use them with water and air.

Also known as wafer ball valves, these combine the slim body of a butterfly valve with the high flow rates of a flanged ball valve. They bolt to ANSI flanges. Use with water, oil, air, inert gas, and steam.

Clean and maintain these valves without removing welded connections. They have a three-piece bolted body that disassembles inline for easy access to internal components. Use with water, oil, air, inert gas, and steam.

Solder these valves to metal tubing for a permanent, leak-tight connection. Use with water, oil, air, inert gas, and steam.

For more durability than plastic valves, these are made of metal. A compression sleeve bites into tubing as you tighten the nut, forming a strong seal. Use these valves with water, oil, air, inert gas, and steam.

To withstand aggressive and corrosive solutions in miniature chemical-processing pipelines, these tiny valves have a chemical-resistant fluoroelastomer seal and a corrosion-resistant 303 stainless steel body.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a plastic body and a chemical-resistant seal.

With a forged steel body and bolted construction, these durable valves can withstand nearly 10 times the pressure of other socket-weld gradual on/off valves.

These solenoid valves operate on electricity to automatically start and stop flow. The actuator is directly mounted to the valve body to minimize movement and reduce wear.

Lower profile and available in smaller connection sizes than standard valves, these fit in tight spots.

Comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series, these valves meet the highest quality standards.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

Designed for controlling single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

For use in general purpose applications with water, oil, and inert gas.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

Also known as butterfly valves.

Use air pressure to automatically control the flow of liquids in sanitary environments, such as food and beverage processing plants.

For general purpose applications with water, oil, and inert gas.

With a slimmer motor than other motor-driven valves, these fit in tight spots.

Their ball valve design allows these valves to handle three times the flow of butterfly valves.

Valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Also known as whistle valves, these open and throttle as force is applied to the lever and automatically close upon release. They’re commonly used for spraying, washing, and other applications that require manual discharge of liquid and air. Use with water, oil, air, and inert gas.

For a longer service life than other flanged flow-adjustment valves, these are designed to open and close with minimal wear on internal components. Use with water, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a low-profile body and a narrow port-to-port length, these valves fit in tight spots. Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

These valves divert flow between ports. Use with water, oil, air, and inert gas.

Also known as shuttle valves, these automatically switch the inlet source as pressure changes; they always direct flow from the higher-pressure side-port inlet to the top-port outlet. Use them with water, oil, air, and inert gas.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

Control flow in two directions from a single source—these valves have two handles for independent operation of each outlet. Use them with water, oil, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

These valves operate on electricity to automatically divert flow between ports. Use with water, oil, air, and inert gas.

Often used for emission analysis and gas processing, these valves attach to each other horizontally to create one centralized manifold for servicing multiple process lines. All are rated for use with water, oil, air, and inert gas. They operate on electricity to automatically divert flow between ports.

For use with threaded pipe, these valves have NPT connections. Use them with water, oil, air, and inert gas. All operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.

For use with threaded pipe, these valves are available with NPT, NPTF, BSPP, BSPT, and UNI/UNF (JIC) connections.

Plastic provides a lightweight alternative to metal.

With few moving parts to wear out, these valves withstand frequent opening and closing, pulsating flow, and rapid flow reversal.

Barbs grip onto tubing, providing a secure hold.

Two sleeves give the fittings extra gripping power. They bite into tubing as you tighten the nut to form a strong seal. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Less than half the end-to-end length of standard flange-mount check valves, these can be installed in pipelines with limited clearance.

Weld to unthreaded metal pipe.

Insert tubing into the fittings—no heat, solder, or flux required.

Commonly used with irrigation systems and laboratory equipment, these valves have NPT connections.