Give switches and outlets a finished look.

Keep switches and outlets under cover for protection from dust and dirt. These stainless steel plates resist corrosion and have a sealing gasket to keep out moisture.

Pair wall plates and adapters to create a custom cover for existing receptacles and switches to give them a rejuvenated look, no rewiring required.

Snap end and center sections together to create your own two-device or wider wall plate.

Close off unused switches.

Knockouts allow you to modify these boxes to fit your application.

Knockouts allow you to modify these boxes to fit your application.

Add depth to your outlet box.

Close off unused outlets.

Close off unused outlets.

Add depth to octagonal outlet boxes.

Mount these boxes to the outside of an enclosure to access a programmable logic controller or other networked device without opening the enclosure.

Use the built-in connections to attach conduit without using fittings.

These boxes have an open back to accommodate extra-deep low-voltage devices.

Mount these boxes on the surface of your wall in areas where you can't create a recess.

These boxes come ready to use with receptacles installed.

These corrosion-resistant boxes are built to withstand exposure to rain, snow, and wet conditions.

Rain, snow, and wet conditions won't damage these corrosion-resistant covers.

Close off unused outlets.

These corrosion-resistant covers can withstand rain, snow, and wet conditions without being damaged.

After installing in drywall, cover the perforated flange with drywall compound and only the panel will be visible for a clean finish.

Designed for use with circular cutouts, these panels have gaskets that form a tight seal to keep out dust and moisture.

Panels are insulated to prevent heat from passing through.

Commonly used in offices, hospitals, and schools, these guards protect corners on walls and other surfaces from impact.

Even in the dark, these black and yellow striped guards draw attention to equipment and obstructions. They protect corners on walls, posts, shelving, and other surfaces from damage.

Combine corner guards, surface guards, and end caps to create a system that protects walls and equipment from impact and wear. Often used in offices, hospitals, and schools, these systems protect against damage from small carts and chairs.

Protect walls and other surfaces from impact.

Vibrant colors create a visual alert to draw attention to equipment and obstructions. These guards protect walls and other flat surfaces from impact.

These aluminum bases provide more impact protection than plastic bases. In addition to protecting the bottom of a wall from damage, they create a finished look where the wall meets the floor. They're commonly used in warehouse and manufacturing areas.

Often used to protect sheet metal during fiber and CO2 laser cutting, this film is also good for other fabrication processes such as bending, stamping, and forming. You can even leave this film on finished parts for protection against damage during shipping and storage.

With its reflective, mirror-like finish, this film is often used to repair or create new decorative finishes on edge trim, panels, and other flat surfaces.

Made of woven polyethylene fabric, this is the most puncture-, abrasion-, and tear-resistant surface protection we offer. Commonly used on heavy equipment, it guards metal, plastic, composite, and painted surfaces from damage. It can also be used as a protective layer beneath other materials.

Virtually unbreakable, these clear panels are impact, heat, chemical, weather, and UV resistant.

Cover the opening where air is pulled into your HVAC system.

Guide air toward your workspace or deflect unwanted drafts with these diverters and covers.

These gravity-operated louvers remain open only when air flows, preventing backdrafts.

Get an exact fit for your opening by sliding out these louvers to the width you need.

Constructed with a thick frame and blades, these louvers have a long service life.

Always open, these are our most basic wall louvers.

Relieve heat buildup and prevent condensation from forming inside enclosures and other small spaces.

Includes one 1-1/2"×3"×0.032" thick piece of each texture: weave, diamond, and tread.

For use with washdown receptacles, these outlet boxes withstand corrosive and washdown environments.

Use these primers in enclosed occupied areas, such as hospitals, schools, and offices. They cover stains and prepare your surface, extending the life of paint and coatings.

Prepare metal, wood, and concrete for paint. Primers adhere to underlying surfaces to create a base layer that bonds well with paint for a long-lasting finish.

Use this zero-VOC primer on drywall in enclosed occupied areas, such as hospitals, schools, and offices, to extend the life of paint.

Use these primers on concrete floors before antislip coatings to maximize longevity.

Make items stand out under emergency lighting or in low-light environments.

Create a washable writing surface.

This zero-VOC paint is for use in enclosed occupied areas, such as hospitals, schools, and offices.

Eliminate paint splatter clean-up—drops dry to a powder as they fall from ceilings 10 feet and higher.