Flip a clamp onto your wire instead of crimping to speed up installations, then reuse these connectors later. The clamp secures and disconnects wires without damaging them. Choose these connectors for setups that change often, such as prototypes and testing. They even have test sockets to safely test voltage after installation.

DIN Rail Mounting Adapters—Clip connectors onto DIN 3 rail to keep them organized and easily accessible.

Covers—Seal out moisture to protect your connection. Covers are lined with a sticky gel, so you don't need to mix or pour a potting compound yourself. They’re rated IP08 to withstand splashes, rain, and humidity. To repair or expand your circuit, open the cover and remove the wires so you can reuse them. However, you'll need to replace the splice and cover after you open the cover and remove the gel.

A step up in grip strength and strain relief over standard butt splices. After crimping your splice, apply a heat gun to shrink the plastic and grip wire securely under tension and vibration. The heat shrink also protects wire from the drips, dirt, and scuffs that lead to fraying, poor conductivity, and short circuits.

Our strongest-gripping butt splices secure wire through heavy vibration and sharp tugs.

Seal out dust and moisture to protect splices, terminals, and other electrical connectors. These covers are lined with a sticky gel that encapsulates the electrical connector. The seal created by the gel helps them meet IP08 standards—use them in junction boxes and outlets exposed to high humidity, rain, and splashing water. Unlike potting compounds, you don't need to mix or pour the gel before you install these covers.

If you have to expand or repair a circuit, you can open these covers and use the wires again. However, once you open the cover and remove the gel, you’ll need a new electrical connector and cover.

The choice for outdoor electrical panels, HVAC systems, and anywhere you're concerned about moisture. A gel filler repels moisture to keep your wires dry and conductive.

These connectors bite through insulation, so you save time and avoid damage from a wire stripper. For the most dependable connection, use a crimping tool to squeeze connectors onto your wire.

A step up in grip strength and conductivity from standard wire connectors. Twist your wires together and crimp them so they hold securely when tugged or jostled. For rain and splashes, choose heat-shrink crimp-on wire connectors instead. For wires on or around vibrating equipment, consider tight-hold heat-shrink connectors.

Add a new branch to your circuit the quick way—no need for a new power source or a wire stripper. These taps bite through insulation to draw power from an installed main wire to new tap wires. Slide in the unstripped main and tap lines, then close the tap and squeeze it with a crimper for a secure connection.

Insert wires end to end and lock them in place with the twist of a cap. These splices resist vibration and pulling to keep a secure connection between wires. They're convenient for field installations when you don't have crimping tools handy.

Twist onto the wire instead of crimping for fast and easy installation.

Unlike other wire taps, a gel filler repels moisture to keep your connection dry and conductive. These taps bite through insulation to draw power from an installed main wire to a new tap wire. No need to cut or strip your wire—slide in the main and tap lines, then close the tap and squeeze it with a crimper for a secure connection.

A gel filler seals out water to keep your wires completely dry and conductive. No need to strip your wire—insert insulated wires into the splice, then squeeze the button with a crimper or pliers until it clicks. The splice bites through the insulation, so you don't take extra time or risk nicks and cuts from a wire stripper. Snap splices together to create the exact setup you need.

One splice does the job of two—connect a single wire with two others of the same size to streamline your run. After crimping the splice, apply a heat gun to shrink the plastic and grip wire securely under tension and vibration. The heat shrink also protects wire from the drips, dirt, and scuffs that lead to fraying, poor conductivity, and short circuits.

Our strongest-gripping reducing butt splices hold wire securely through heavy vibration and sharp tugs. Also known as step-down splices, reducing splices join a larger wire and a smaller wire end to end. Colored stripes differentiate the larger and smaller openings so you don't have to measure and mark them yourself.

An upgrade in strength and strain relief over standard reducing splices. After crimping your splice, apply a heat gun or butane torch to shrink the plastic and grip wire securely under tension and vibration. The heat shrink also protects wire from the drips, dirt, and scuffs that lead to fraying, poor conductivity, and short circuits. Also known as step-down splices, reducing splices join a larger wire and a smaller wire end to end. Colored stripes differentiate the larger and smaller openings so you don't have to measure and mark them yourself.

A step up in grip strength and strain relief over standard multi-direction splices. After crimping your splice, apply a heat gun to shrink the plastic and grip wire securely under tension and vibration. The heat shrink also protects wire from the drips, dirt, and scuffs that lead to fraying, poor conductivity, and short circuits.

These splices streamline wiring for industrial control panels, automotive electrical systems, and other complex setups. The wires come together at the center of the splice like spokes on a wheel, contacting the hub without touching each other.

Unlike other crimp-on butt splices, a grease filler repels moisture to prevent corrosion and keep your wire dry and conductive. Attach your wire with a crimping tool to avoid a damaged splice and loose connection.

These connectors are as quick to install as our clamp-on option, though they're not as easy to adjust. They extend or terminate electrical connections in branch circuits, such as light fixtures and electronic devices. Push wire into place without the need for an installation tool. To break the connection later, you'll have to pull wire back out. The connectors also have test sockets to safely test voltage after installation.

DIN Rail Mounting Adapters—Clip connectors onto DIN 3 rail to keep them organized and easily accessible.