After extending to full length to provide added reach, this cable retracts and self-coils for tangle-free storage. It's often used with hand tools and other portable devices.

Ultra-flexible cable extends and retracts more easily than flexible cable.

SVO cable has an oil-resistant outer insulation. SJOW, SOW, SJEOW, and SEOW cable have an oil- and water-resistant outer insulation. SJOW and SOW have a multipurpose neoprene insulation. SJEOW and SEOW have a TPE rubber insulation that also withstands chemicals.

The insulation on this cable withstands high-heat applications such as ovens and furnaces. The wires are silver or nickel plated for corrosion resistance.

Use unshielded cable in applications where signal interference is not a concern. It has a layer of fiberglass fabric and mica tape around each wire. The entire cable is wrapped in a layer of fiberglass fabric and mica tape, and then covered in PTFE. The PTFE outer insulation resists chemicals, oil, abrasion, and moisture.

Shielded cable has a layer of braid that blocks signal interference from nearby equipment and devices. It has PTFE outer and inner insulation that resists chemicals, oil, abrasion, and moisture.

Weather-resistant insulation makes this cable suitable for outdoor use and direct burial without conduit.

18-gauge wire is often used for sprinkler systems.

Often used in automated applications such as robotics and cable carriers, this cable withstands continuous motion without degrading data or signal transmission. It’s flame rated VW-1 to meet requirements for preventing the spread of flames based on a timed test with vertically suspended material. Rated for use in ISO Class 1 or ISO Class 2 clean rooms, this cable releases minimal particles into the air, helping you to maintain the cleanest possible environment.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of braid that blocks signal interference from nearby equipment and devices.

Choose cable with PVC plastic outer insulation for general purpose indoor applications. Their protective layer resists abrasion, though it has the highest bend radius compared to other materials.

CE marked cable meets European health, safety, and environmental protection requirements.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the radius, the more the cable can bend.

This cable has an insulation with excellent resistance to oil, so it can be used near motors and equipment that require oil lubrication. Often used in automated applications such as robotics and cable carriers, it withstands continuous motion without degrading data or signal transmission. It’s flame rated VW-1 to meet requirements for preventing the spread of flames based on a timed test with vertically suspended material.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of braid that blocks signal interference from nearby equipment and devices.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

Rated to 17,000 volts AC or higher, this cable is often used in oil drilling, robotics, and festoon systems. It withstands continuous motion without degrading data or signal transmission. With a flat shape, it’s good for tight spaces. It meets UL 94 V-0 for flame retardance.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

In addition to handling continuous movement, this cable withstands twisting up to 450° without degrading data or signal transmission. It's often used in welding robots and rotary tables. It’s flame rated VW-1 to meet requirements for preventing the spread of flame based on a timed test with vertically suspended material. The polyurethane rubber insulation resists abrasion and oil.

Use unshielded cable in applications where signal interference is not a concern.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

With a life span of more than 20 million high-speed flex cycles, this cable lasts twice as long as standard continuous-flex cable so you have to replace cable less frequently. Often used in automated applications such as robotics and cable carriers, it withstands continuous motion without degrading data or signal transmission. The polyurethane rubber insulation resists abrasion, chemicals, and oil.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

For use in tight spaces, this cable has up to a 40% smaller OD than standard continuous-flex cable so it fits in tight spaces. The inner insulation is modified polyphenylene ether (mPPE), making the cable nearly half the weight of standard continuous-flex cable. Often used in automated applications such as robotics and cable carriers, it withstands continuous motion without degrading data or signal transmission.

Bend radius is the point to which the cable will bend without being damaged. It is measured from the center of the bend to the edge of the cable. The smaller the measurement, the tighter the bend.

This cable is designated CL3R and CMR, so it has flame-resistant insulation and is approved for use in low-circuit circuits in vertical shafts and large facilities with multiple levels. It’s often used in intercoms, speakers, and security systems.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of foil that blocks signal interference from nearby equipment and devices. It has an uninsulated ground wire is not counted in the number of wires.

Also known as plenum cable, this cable is designated CL3P and CMP, so it has flame-resistant, low-smoke insulation and can be used without conduit in duct work and above a drop ceiling. Use it in low-current circuits such as intercoms, speakers, and security systems.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of foil that blocks signal interference from nearby equipment and devices. It has an uninsulated ground wire that is not counted in the number of wires.

Hook up thermostats, air-conditioning units, and other low-voltage equipment. This cable is designated CL2 so it has flame-resistant insulation. The wires are solid so it stays in the shape you bend it.

Use unshielded cable in applications where signal interference is not a concern.

Shielded cable has a layer of braid that blocks signal interference from nearby equipment and devices.

This cable meets TC-ER crush and impact requirements for exposed runs in cable carriers, so it can be used without conduit. It withstands period flexing and bending, sends signal and data to operate, measure, or regulate automated equipment. The PVC insulation resists oil. It’s flame rated FT4 to meet requirements for preventing the spread of flames based on a timed test with material mounted to a vertical tray.

Use unshielded cable in applications where signal interference is not a concern.

Double shielded cable has a layer of braid and foil shielding that provides excellent protection against signal interference from nearby equipment and devices.

Nearly two-thirds the diameter of standard control cable, this cable fits in tight spaces. The modified polyphenylene ether (mPPE) insulation is less than half the weight of the PVC insulation found on standard control cable, yet is more abrasion and cut resistant. Use it to send signal and data to operate, measure, or regulate automated equipment that requires cable to periodically flex and bend. It’s often used with conveyors, CNC machines, and to connect equipment to a control panel. Cable is flame rated VW-1 to meet requirements for preventing the spread of flames based on a timed test with vertically suspended material.

Use unshielded cable in applications where signal interference is not a concern.

Double shielded cable has a layer of braid and foil shielding that provides excellent protection against signal interference from nearby equipment and devices.

Cords with a 90° elbow plug fit flush against a wall outlet, so they fit behind machinery or in areas where space is tight.

SVT cords are ultra-flexible and as pliable as vacuum cleaner cords. They withstand repeated winding.

Use SJT cords in dry or damp locations.

Designed for indoor applications, these cords are often used to power appliances.

SPT cords have a flat cord shape so they fit in tight spaces. The numbers 1, 2, and 3 indicate the relative thickness of the insulation. SPT-3 is the thickest, so it is less flexible but more durable than -1 and -2 cords.

Use SJT cords in dry or damp locations.

These self-coiling cords stretch to full length and then return to their retracted length for tangle-free storage. The industry designation is SJEOW, so the insulation resists oil and water.