Bring light to areas that don't have electrical power service.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Hang these lights where you need them on the job site.

Keep excess cords out of your way—the reel locks the cord at any length and retracts it when not in use.

Hang these lights above your workspace—they shine through long tubes to distribute even light with minimal glare and shadows. Carry them where you need them and suspend them from pipes, beams, and other overhead surfaces.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, Class II, and Zone 1.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Bring light to remote, wet areas. These floodlights are IP rated to handle humidity and dripping, splashing, and falling liquids. Adjust their tripod up and down to direct light as far as you need.

These lights cast a narrow beam of light. With a gooseneck arm, they are faster and easier to reposition than articulating-arm lights.

These lights have a longer reach and hold their position better than gooseneck-arm lights, especially around vibration.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Pivot the head to cast a narrow beam of light to exactly where it's needed.

Though not as bright as our miniature fiber-optic lights, these lights have built-in LEDs that last longer, are more efficient, and are more affordable.

No need for wiring—these lights plug-in with a two-prong plug. Also known as shop lights.

Also known as strip or channel lights, the ends of these fixtures are designed to be wired together to create long rows of lights.

Fit traditional fluorescent ceiling strip lights with LED lights, which use less electricity.

Update standard outlet boxes in closets, hallways, and storage rooms to use LED light.

These lights fit into ceiling cutouts.

Also known as troffers, these lights fit most standard drop-ceiling grids.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

These lights mount to the wall so they're often used in enclosed spaces such as stairwells, hallways, and storage rooms.

Customize these lights to label doors or areas of a building.

With a lower profile than other bay lights, linear bay lights mount closer to ceilings, providing more room for racks or shelving.

Also known as pigtail holders. Temporarily wire these sockets to provide light during construction.

These lights produce a wide beam of uniform light to fill large, open areas with ceilings up to 18-ft. high.

Also known as jelly jar lights. These fixtures have a guard that protects the lens from breaking.

A sealed lens keeps moisture out to protect these lights against washdowns.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs.

Also known as grow lights, these lights encourage growth in herbs, flowers, and other plants indoors.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

Small enough to fit in your pocket.

These flashlights are built to handle everyday use. They have a slip-resistant grip to ensure a secure hold.

Clip these little flashlights to a baseball cap or a surface to light up your work.

Plug in these flashlights and they’ll automatically light up when the power goes out. There’s no need to regularly replace the batteries—they recharge on the base when it’s plugged into an outlet.

Shine light into hard-to-reach spaces with these flexible-arm flashlights.

Always have a flashlight on hand—these attach to a key ring.

Free your hands for other work by mounting a flashlight to a nearby surface.

Convert incandescent, halogen, krypton, and xenon Maglite flashlights into LED flashlights to produce more light and consume less battery power.

In addition to pivoting 210°, the light heads rotate 360° for directing light exactly where it’s needed. They're rated for use in environments where hazardous material is present.

Rated for use in environments where hazardous material is present.

All of these flashlights stand up to wet environments.

Keep your hands free by wearing a flashlight on your head.

Light up work even when your visor is up. These headlamps come with three attachments that fit with anything from your hard hat to your baseball cap.

Light up work without risking an explosion. NEC rated, these headlamps are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Illuminate small spaces and mark locations with these reusable lightsticks.

With a slimmer profile than other strip machine lights, these lights fit in tight spots on workspaces and inside machinery because they don’t have a circuit board.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

These classic-style machine lights have a reflector to distribute light more evenly than strip machine lights.

Suspend these lights overhead or mount them above your workspace.

No need for wiring—these lights plug-in with a three-prong plug.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Mount this light on a pole to illuminate pedestrian areas such as streets and walkways.

Heads adjust to any angle so you can direct light where needed.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Compared to other dock lights that can only adjust vertically and horizontally, these lights bend at any angle to direct light exactly where it's needed.

A sealed head and switch keeps these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Mount add-on heads in remote areas to extend emergency lighting.

Rated for use in damp locations, these lights withstand humidity and moisture.

No need for wiring—these lights plug-in with a two-prong plug.

More securely mounted than weighted-base magnifiers while taking up less space on your work surface, these illuminated magnifiers clamp to the side of a workbench.

Capture the extra-fine details you see under the magnifying lens in a photo or video.

For a steady view of fine details even near vibrating machinery, lock each joint on the arm.

Two LED bulbs illuminate your work.

Sturdy but flexible, these illuminated magnifiers have a weighted base to keep them still without tethering them to your workbench.