Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.

The removable flat head provides a flush finish in countersunk holes.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

Drive these tools with a hammer to expand anchors.

Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.

Also known as lag shields, these anchors are designed for use with large-diameter wood screws.

Also known as drive rivets, install by hammering the screw into the body. Unthread the screw to remove.

Bolts are beveled under the head for a flush finish in countersunk holes.

A pivoting toggle bar creates a strong hold.

A spring-loaded toggle holds against the back of the material.

Bolts are beveled under the head for use in countersunk holes.

A shallow head makes these bolts good for low-clearance applications.

Wedge these hangers in concrete and other solid materials.

These hangers are a popular choice for overhead applications.

Drill holes with the point on these hangers.

Drive these hangers into wood with an adjustable wrench, pliers, or a special driver bit.

Join two beams in a straight line.

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Support strut channel at a right angle to the beam.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

Also known as footman's loops, use these guides to prevent webbing from twisting, or as anchor points in tie-down applications.

Use these plates where full lengths of track won't fit to create one anchor point.

Create a loop by feeding the wire rope through the clamp and tighten the set screw to secure it in place. Loosen the set screw to quickly adjust the loop. Also known as Gripple rope clamps. They are for use in noncritical applications, such as fencing.

Make a removable loop without specialty tools for use in noncritical applications, such as fencing. Also known as tiller clamps.

These thimbles are also known as thin pattern thimbles.

Install these swivel-hook-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these eye-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Use these eyebolts for routing wire and for other light duty applications.

Lock by screwing the latch into the body.