McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    6 Products
    About Pumps
    industrial info icon

    Measure how high and far your system needs to move liquid. Then compare pumps by priming methods and flow control types.

    Harsh-Environment Low-Maintenance Plastic Circulation Pumps for Water and Coolants

    Image of Product. Front orientation. Centrifugal Pumps. Harsh Environment Low-Maintenance Plastic Circulation Pumps for Water and Coolants.
    These pumps have a totally enclosed fan-cooled (TEFC) motor for use in dusty, dirty, and damp environments. The impeller is turned with magnets to eliminate seal wear and leakage for a long service life. Pumps are often used with electroplating and photographic solutions. They are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.
    Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.
    Temp.,
    ° F
    Overall
    Max. Flow
    Rate, gpm
    Flow Rate @ 10 ft.
    of Head, gpm
    Max. ft. of
    Head, ft.
    Max. Pressure,
    psi
    Min.
    Max.
    Power,
    hp
    Current
    Intake Connection
    Type
    Discharge Connection
    Type
    Lg.
    Wd.
    Ht.
    Each
    120V AC, Single Phase—With Thermal Overload Protection
     
    Plug In—20 cP Maximum Viscosity
    10616.37351501/251.3 amp1/2 Female NPT1/2 Male NPT9"4"5"99095K510000000
     

    Low-Maintenance Plastic Circulation Pumps for Water and Coolants

    Eliminate seal wear and leakage with pumps that use magnets to turn the impeller. They’re often used with electroplating and photographic solutions. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.
    Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.
    Pumps with Tube Connections (Front Intake)
    Image of Product. Front orientation. Centrifugal Pumps. Low-Maintenance Plastic Circulation Pumps for Water and Coolants, Pumps with Tube Connections (Front Intake).
    Flow
    Rate, gpm
    Intake
    Discharge
    Overall
    Max. Flow
    Rate, gpm
    @ 5 ft.
    of Head
    @ 10 ft.
    of Head
    Max. ft. of
    Head, ft.
    Max. Pressure,
    psi
    Max. Viscosity,
    cP
    Temp. Range,
    ° F
    Power,
    hp
    Current,
    amp
    Connection
    Connection
    Type
    For Tube
    ID
    Connection
    Connection
    Type
    For Tube
    ID
    Lg.
    Wd.
    Ht.
    Each
    120V AC, Single Phase—With Thermal Overload Protection
     
    Plug In
    7751982035 to 1501/251.65Barbed
    		Male Unthreaded5/8"Barbed
    		Male Unthreaded5/8"8 1/4"3 1/2"5 1/4"9930K410000000
     

    Extended-Life Inline Circulation Pumps for Water

    Image of Product. Front orientation. Centrifugal Pumps. Extended-Life Inline Circulation Pumps for Water.
    Eliminate seal wear and leakage—these pumps have magnets that turn the impeller for a long service life. Install them directly in your pipeline for applications such as hot-water circulation and hydronic heating and cooling. Mount vertically or horizontally. Do not run dry or use with solids.
    Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.
    Flow
    Rate, gpm
    Temp.,
    ° F
    Overall
    Max. Flow
    Rate, gpm
    @ 5 ft.
    of Head
    @ 10 ft.
    of Head
    Max. ft. of
    Head, ft.
    Max. Pressure,
    psi
    Min.
    Max.
    Power,
    hp
    Current
    Intake Connection
    Type
    Discharge Connection
    Type
    Lg.
    Wd.
    Ht.
    Each
    120V AC, Single Phase—With Thermal Overload Protection
     
    Plug In—1 cP Maximum Viscosity
    65312.1150352501/250.54 amp1/2 Male NPT1/2 Male NPT4 7/8"3 1/2"7 1/2"4161K210000000
     

    High-Flow Extended-Life Inline Circulation Pumps for Water

    Image of Product. Front orientation. Centrifugal Pumps. High-Flow Extended-Life Inline Circulation Pumps for Water.
    These pumps have higher flow rate than other inline circulation pumps and are cooled by the liquid being pumped to extend the life of the motor. Install them directly in your pipeline for applications such as hot-water circulation and solar heating. Pumps have an open dripproof (ODP) motor for use in clean, dry, and well-ventilated environments. Mount horizontally with required pipe connectors (sold separately). Do not run dry or use with solids.
    Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.
    Required Pipe Connectors—When ordering the required pipe connectors (sold separately), please specify pipe size of ¾, 1, 1 ¼, or 1 ½.
    Pumps
    Required Pipe
    Connectors
    Temp.,
    ° F
    Overall
    Max. Flow
    Rate, gpm
    Flow Rate @ 10 ft.
    of Head, gpm
    Max. ft. of
    Head, ft.
    Max. Pressure,
    psi
    Min.
    Max.
    Power,
    hp
    Current
    Intake Connection
    Type
    Discharge Connection
    Type
    Lg.
    Wd.
    Ht.
    Each
    Pair
    120V AC, Single Phase—Without Thermal Overload Protection
     
    Hardwire—1 cP Maximum Viscosity
    22815150402301/250.8 ampFemale NPTFemale NPT5 5/8"4 7/8"6 3/8"8174K8100000008174K8000000
     

    Submersible Pumps for Water

    Image of Product. Front orientation. Submersible Pumps. Submersible Pumps for Water, Style B.

    Style B

    Submerge these pumps to circulate water in small tanks, cooling baths, fountains, and other low-flow applications. Plug in to activate. Do not run dry. Not for use with salt water or flammable liquids.
    Style B
    Image of Product. Front orientation. Submersible Pumps. Submersible Pumps for Water, Style B.
    Max. Flow
    Rate, gpm
    Discharge
    Overall
    @ 1 Ft.
    of Head
    @ 5 Ft.
    of Head
    Max. ft. of
    Head, ft.
    Temp. Range,
    ° F
    Power,
    hp
    Current,
    amp
    Intake Inlet
    Type
    Pipe
    Size
    Thread
    Type
    Gender
    Cord Lg.,
    ft.
    Ht.
    Wd.
    Dp.
    Each
    115V AC, Single Phase—Without Thermal Overload Protection
     
    Plug In
    3.51.57.135 to 851/250.5Screened1/4
    		NPT
    		Male63 7/8"3 1/2"4 5/8"3163K32000000
     
    back to top