These pumps have the best chemical resistance of all our circulation pumps. Instead of a shaft seal, they use magnets to turn the impeller, reducing wear and leakage. The motor is totally enclosed fan-cooled (TEFC) for use in dusty, dirty, and damp environments. Pumps are gravity fed and require an elevated liquid source. Do not run dry or use with solids.

Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.

Commonly called rotary vane pumps, these are designed to pump water at high pressures in low-flow applications. Motor is open dripproof (ODP) for use in clean, dry, and well-ventilated environments. They have a built-in bypass relief valve to prevent pressure buildup. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.

Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.

Alter the flow rate for versatile dispensing. These pumps do not include a drum connector.

Operating on a 12-volt battery, these pumps transfer and drain fuel such as gasoline, diesel fuel, and kerosene. Lock the nozzle with a padlock (not included).

Always bond and ground your application for static control. For more information about bonding and grounding, see Sections 1910.106 and 1910.107 of the Federal OSHA Code or see bonding and grounding equipment.

Pumps with metering nozzle record total volume up to 99,999.9 gallons.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump. Mount up to 6 feet above your liquid source. Pump can pass solids up to 1/4" in diameter without clogging, so there’s no need to filter sediment and debris. A handle makes it convenient for on-the-go removal of bilge water, waste oil, and spills. Pump can also be used to cool marine engines and drain liquid from holding tanks.

Note: Pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

Clean up water in flooded areas without a sump pit. Install these pumps in debris-free water that’s at least 2" deep. They activate when plugged in. You can add a plug-in switch to control when the pump activates. Submerge while in use.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Install them in debris-free water that’s at least 2” deep. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Submerge while in use.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Remove accumulated water from sump pits, loading docks, and cooling towers. The float switch is wired to the pump. Use with debris-free water. Submerge while in use and do not run dry.

For high-volume chemical sampling and draining, these pumps have a powerful motor that enables them to move 2,448 gallons of liquid per day. They're commonly used with ammonia, acid-washing solutions, and cleaning fluids. Motor is open dripproof (ODP) for use in clean, dry, and well-ventilated environments. Pumps are self-priming and create a suction force to draw liquid upward. Mount up to 15 feet above your liquid source. They can run dry. Do not use with solids.

Equipped with a built-in container for condensate, these pumps work alongside your system to remove condensate from air conditioners, refrigerators, dehumidifiers, and other equipment. They are not submersible. A safety switch turns off your equipment in case of pump failure. Pumps turn on and off automatically.

Hardwire pumps must be wired to a power source.

Style D pumps withstand higher temperatures than the other styles.

Designed for use in low-pressure steam systems, these pumps capture steam in the attached tank and return hot condensate to your boiler or feed unit. They are activated by a float switch, turning on and off when condensate level reaches a certain depth.

Pumps with cast iron tank are for continuous use and have a longer service life than carbon steel.

Maintenance kit for pump with cast iron tank includes a shaft, a bushing, a thrust washer, a spring washer, an oil seal, and snap rings.