An aluminum enclosure around the motor provides protection in dusty and dirty environments. Designed to fit into small equipment, these pumps have miniature gears and a subfractional horsepower motor for low-flow applications. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry or use with solids.

Note: If flow control is needed, place valves or reducers on the discharge side; never restrict the inlet of a pump with a valve or reducer.

For technical drawings and 3-D models, click on a part number.

For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

Operating on a 12-volt battery, these pumps transfer and drain fuel such as gasoline, diesel fuel, and kerosene. Lock the nozzle with a padlock (not included).

Always bond and ground your application for static control. For more information about bonding and grounding, see Sections 1910.106 and 1910.107 of the Federal OSHA Code or see bonding and grounding equipment.

Pumps with metering nozzle record total volume up to 99,999.9 gallons.

Remove water in locations without power with these battery-operated pumps. Do not run dry.

Continuous duty pumps attach to a 12-volt battery. They are gravity fed and require an elevated liquid source to fully fill the pump before turning on.

For technical drawings and 3-D models, click on a part number.

This pump has an impact-resistant aluminum housing and handles larger solids than other battery-operated water-removal pumps. Attach it to a 12-volt battery to remove water in locations without power. Pump is gravity fed and requires an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit. They have an internal sensor, so they turn on when they detect water and turn off when the water is removed. Pumps are fully submersible. They are gravity fed and require an elevated liquid source to fully fill the pump before turning on.

Pumps for 12 volts DC work with 12-volt batteries.

With a footprint that's only a few inches in any direction, these pumps fit into compact systems to dispense small amounts of acids, cleaning fluids, and other chemicals. They're often used in sterilization, photochemical, and water treatment systems. Choose from pumps with either a 4-20mA or 1-5V DC input signal that controls the flow rate.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Dispense precise amounts of fluid from a syringe. Commonly used in chemical and pharmaceutical research, fiber production, and equipment calibration, these pumps maintain a steady flow rate for accurate filling and measuring. Use the color touchscreen to set parameters such as flow rate, force, and volume; schedule start and stop times; and create and save custom operations. Pumps work with glass, plastic, and stainless steel syringes from 0.5 µl to 60 ml. Mount horizontally or vertically; the touchscreen rotates.

These air compressors/vacuum generators are continuous duty and must be hardwired. They do not require lubricant and produce nonlubricated air.

Get compressed air from a DC power source—these compressors can run on a 12-volt vehicle battery (not included) for use on trucks and heavy equipment, or a DC generator. Use them to inflate tires, clean filters, and operate light-duty tools, such as nailers, hammers, and small impact wrenches. For best results with a vehicle battery, use a deep-cycle, large-cell battery rated for continuous use.

Compressors with tank are mounted on a 10-gallon storage tank to handle more demanding applications, such as grinders, saws, and spray guns.

Optional mounting brackets allow you to mount a compressor to a vehicle chassis. Connector assemblies come with a three-foot hose and a connector that can be fixed to a panel or frame for operating compressors installed in difficult-to-reach locations, such as under a vehicle.