Encase electronic assemblies in a layer of urethane for protection from dust, moisture, chemicals, mechanical shock, and vibration. Urethanes withstand a wide range of temperatures and are the best choice for cold-temperature applications. They have excellent flexibility, good chemical and moisture resistance, and provide good electrical insulation.

Cartridge potting compounds can be applied precisely through the included mixer nozzle. You’ll need a dispensing gun (sold separately). US2350™ also require a 4:1 plunger (sold separately) to dispense.

Bottle potting compounds are easier to apply in high volumes than cartridge potting compounds. Mix the compounds together and pour them over components inside potting boxes and other containers. If mixing introduces any air bubbles, put the mixture in a vacuum chamber.

Compounds that cannot be sold to the listed areas are restricted by product labeling requirements.

From shore to sea floor, these potting compounds are formulated for permanent submersion in water—even salt water. Use them to protect circuits and splices in pumps, underwater lighting, and other underwater electronics from corrosion and chemicals. Made of urethane, they withstand a wide range of temperatures, especially cold underwater conditions. They provide good electrical insulation and have excellent flexibility. Since they’re more flexible than epoxy compounds, they’re often used to protect against vibration and impact.

Mix the two parts of these compounds together and pour them over components inside a potting box or other container. If mixing causes air bubbles, put the mixture in a vacuum chamber to remove them.

In just 20 seconds under a UV light, these urethane compounds form into a strong protective layer on electrical components. They withstand a wide range of temperatures and are good electrical insulators. They also stop chemicals, moisture, and dust from damaging your device. With excellent flexibility, they protect against vibration and impact. Since they also work as an adhesive, you can use them to bond and insulate components such as electrical connectors and thermal switches. No mixing required.

These surface fillers can be used on vertical surfaces without sagging. They repair cracked, worn, and damaged surfaces. The size listed is the combined total of the two parts.

Knead the epoxy-coated patch and resin together to make repairs to pipes, tanks, drums, and containers in the field.

Press these putty surface fillers in place to fill in holes, cracks, and dents. When exposed to sunlight or a UV lamp, they begin to harden immediately.

Epoxy fillers provide better adhesion and more corrosion resistance than polyester fillers.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater. Use them to repair cracked, worn, and damaged surfaces. Size listed is the combined total of the two parts.

Putty fillers come in a stick with a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.

Paste fillers resist alkalies, solvents, gasoline, and oil.

Everything you need to repair cracked, worn, and damaged surfaces—even underwater.

Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.

1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.

Use these two-part fillers to rebuild cracked or worn plastic surfaces. The size listed is the combined total of the two parts.

Surface fillers in a cartridge come with a mixer nozzle, but require a gun (sold separately) for dispensing. For best results, use a primer (sold separately).

Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place. Use with most rigid and semi-rigid types of plastic. They meet NSF/ANSI 61 for use with drinking water.

Also known as Ruby Red lithographer's tape, this semi-clear tape filters out light that can affect film and other photo-sensitive film and equipment.

Certificates with a traceable lot number and product shelf life are available for these products. Download certificates from ORDER HISTORY after your order ships.