Connect quick-clamp sanitary tube fittings—also known as aseptic fittings—for a fast and easy way to access your line.

Connect extra-support quick-clamp fittings for a fast and easy way to access your line.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

Use these rings with quick-clamp high-vacuum fittings.

Fittings are polished to a32 Ra and under finish on the interior.

Transfer liquids and gasses into high-vacuum chambers with these assembled fittings, also known as feedthroughs.

Take samples in sanitary environments—these tube fittings won’t contaminate your lines or force you to pause them.

Unlike other duct hose clamps, these are rated for a maximum work load. Clamps have a quick-release latch that lets you access your line frequently while maintaining your original clamp size.

These clamps have rounded edges and a smooth interior, so they won’t cut into soft hose and tube materials such as silicone. Flip up the slotted hex head screw to quickly release the band.

Also known as manifold flange fittings, these have a clamp-together design that lets you access your line for routine maintenance. Fittings resist acids, solvents, and other harsh chemicals. They won’t deteriorate when exposed to the damaging effects of ultraviolet light, so they’re suitable for outdoor use.

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

For the most demanding jobs, these clamps have almost five times the capacity of standard fast-action bar clamps.

Pull the lever to slide the clamping arm along the bar; release to lock in place.

All adjustments can be made from one end, allowing clamping in tight spaces.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol‐grip handle to lock the clamp in place.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Also known as J-clamps, these provide additional clearance to reach around obstructions and clamp workpieces in recessed areas.

Mount to the top of your workbench.

Squeeze the handles and the jaws will automatically adjust to fit your workpiece.

Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.

The jaws on these tools apply outward pressure for use as a spreader.

Use these tools for light duty clamping. Squeeze the handles to open; release to close.

Clamp thin materials, or use in tight spaces.

These clamps meet DIN VDE 0680-1 for protection against accidental contact with live electrical circuits.

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Extend the handle to reach the clamp into tight spaces.

Set includes 12 clamps and the installation pliers required for positioning and removal.

Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Push the lever to lock the handle and prevent accidental opening.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

Mount these clamps below a surface.

The mounting base secures these clamps to a rail or bar.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Mount the clamp on a lid and the latch plate on the side of a container.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Moving parts are protected by a metal cover when the clamp is engaged to prevent dirt and dust from clogging the clamp.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Secure these clamps to a rail or bar.

Two clamps connected by a pivoting arm hold workpieces at nearly any angle.

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.

For repetitive clamping, turn the holding screw to adjust the opening size one time, and then use the handle to secure and release workpieces.

Push the handle to slide the jaw into place for quicker setup than standard drill-press vises.

Long jaws reach workpieces in recessed areas. These pliers lock in a vise-like grip around a workpiece and stay clamped in place to leave your hands free.

Clamp down on nonreinforced hose and tube to squeeze it shut, eliminating the need to drain the hose when working on pumps, heating and cooling systems, and fuel lines. Squeeze the handles to lock the jaws and these pliers stay in place.

A threaded lever lets you tighten these collars with more torque than other quick-release styles, ensuring that they stay put on your shaft.

Make quick adjustments to these shaft collars with a lever on the side.

Also known as double cams, these complete cam handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Use these handles to keep holes aligned or lift several sheets of thin material. They have a plug that expands to grip the edges inside holes. They are not suitable for permanent installation—use only for temporary mounting.

An on/off magnet control makes it easy to move and attach these brackets to metal surfaces.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Use mounting holes to install these magnets where they are needed; switch them on and off with the handle.

Slide these pin-backed clips in and out of fabric cubicle walls without damage.

Hold lightweight objects, secure covers, and seal bags in sanitary and corrosive environments.

Hang documents or signs from these clips, and they rotate 360° to display your materials at any angle.