Conveyor guides direct and position material.

Bend these guides without any extra equipment to create corners or curves.

Use these guides when positioning static-sensitive material such as electronic equipment.

Use the hole at the end of these rods to attach sensors and accessories without clamps.

Graduated in 1/8" increments, these rods make it easy to align multiple brackets during installation.

Clamps hold guide rails in place or join ends of a rail together.

Also known as cross blocks, connectors join rods at different angles.

Spacers increase the distance between a bracket and the conveyor frame.

These brackets mount to the frame of a conveyor to hold guide clamps.

These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

These tiny carriages and guide rails are sized for electronic and other precision applications.

Mount to vertical surfaces for applications where tight tolerances aren't required.

A handle on the side of the carriage locks the carriage in place.

Use these carriages and guide rails in temperatures up to 300° F.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

Use these carriages and guide rails for light loads where precise movement is not required.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

A handle on the side of the carriage locks the carriage in place.

Combine with a T-slotted rail to add linear motion to your assembly.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

Nylon rollers and aluminum rails make these good for light duty applications.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Compatible with THK guide rails, mount these wipers to carriages to sweep chips and other contaminants out of the way as the carriage moves across the rail.