Quickly and safely mount these relays on 35 mm DIN rail (also known as DIN 3). IP20 rated, they have recessed terminals that prevent fingers and other objects from touching live circuits.

Auxiliary contacts (sold separately) allow you to add a signaling device or control another relay. You can add one auxiliary contact to all of these relays.

For technical drawings and 3-D models, click on a part number.

With no moving parts, these solid state relays last longer, switch faster, and are quieter than mechanical relays. They interface between your controller and components to isolate input and output circuits, which protects components from voltage spikes, amplifies the relay’s signal, and reduces interference for reliable transmission. The included relay socket mounts on 35 mm DIN rail (also known as DIN 3 rail) for fast installation. Relays disconnect from the socket for easy replacement. Rated IP20, they prevent fingers and other objects from touching live circuits.

For technical drawings and 3-D models, click on a part number.

Sealed for safety, these relays are a good choice for hazardous locations where combustible or corrosive gases may be present.

Relays with screw terminals are considered interface relays, so they’re placed between your controller and components to isolate the input and output circuits. This means they protect your component from voltage spikes while amplifying the relay’s signal and reducing interference for reliable transmission. They are often used for switching applications, such as small motors and pilot lights. The included relay socket mounts on 35 mm DIN rail (also known as DIN 3 rail).

For technical drawings and 3-D models, click on a part number.

Control and diagnose issues with safety-critical circuits. These relays have a microprocessor that monitors safety components, such as emergency stops and light curtains, and sends a signal to stop the operation if a failure is detected and restart when the issue is resolved. They also help with diagnostic tasks because of their feedback circuit, which allows basic relays to communicate their status back to the safety relay. These relays have a duplicate set of input and output signals, so they’ll still stop the controlled device if one of the inputs fails.

IP20 rated, they have recessed terminals which prevent fingers and other objects from touching live circuits. These relays have been tested to multiple safety standards and can help achieve PL, SIL, or CAT system ratings. They also meet ISO and IEC standards for machine safety.

Mount them to 35 mm DIN rail (also known as DIN 3 Rail) for fast installation.

Auxiliary contact blocks (sold separately) allow you to control more components, such as signaling devices or basic relays.

For technical drawings and 3-D models, click on a part number.

Control multiple timing functions from your electrical cabinet—these timer relays mount to 35 mm DIN rail (also known as DIN 3 rail), which is the most commonly used size. UL Listed, C-UL Listed, and CE Marked, these relays meet American, Canadian, and European safety standards.

Timer Relays with Delayed, Interval, Switch-On, and Repeat Cycles

With six different functions, these timer relays have a broad range of applications. Use them to precisely control machines such as conveyors, lighting systems, and electric motors.

The delayed start (delay-on-make) function allows you to set how long it takes for the relay to turn on after input voltage is applied. For example, a drill starts pumping lubricant immediately, but it does not start rotating until the set time has elapsed.

The delayed switch-on with delayed switch-off function uses a switch instead of input voltage. It allows you to set how long it takes the relay to turn on after a switch is turned on, and how long it will stay on after the switch is turned off. For example, a furnace turns on, but the fan doesn’t start pushing air through the vents until it has been heated. When the furnace turns off, the fan keeps blowing to circulate all the hot air.

The delayed switch-off (delay-on-break) function uses a switch instead of input voltage. When the switch is turned off, the relay remains on for a programmed amount of time before turning off. For example, a projector’s light is turned off with a switch, but its cooling fan continues to run for a set time.

The interval function uses input voltage to turn on the relay for a programmed amount of time. For example, when a part moving down a conveyor reaches a certain location, a cleaning spray comes on for a set time.

The switch-on (single-shot) function requires a switch to activate the relay, which stays on for the programmed amount of time. For example, lights in a storage room are turned on with a switch and stay on for a set time before turning off.

The repeat cycle function alternates between an on cycle and off cycle of equal durations until input voltage is removed. A common example would be a flashing light.

Timer Relays with Asymmetrical Repeat Cycles

Use these timer relays when your repeat cycles have different on- and off-cycle durations.

The asymmetrical repeat cycle alternates between different durations of on and off for as long as input voltage is applied. For example, a sprinkler system sprays in short bursts followed by longer rest periods, on and off until input voltage is removed.

The switch-on asymmetrical repeat cycle function is activated with a switch instead of input voltage. It could be used to turn on an electric motor for a short period and then turn it off for a longer rest period, repeating that pattern until the switch is turned off.

Turn machinery, such as paint and conveyor lines, on and off after a set period of time. These timer relays plug into relay sockets (sold separately) for fast installation and replacement.

Relay sockets mount on 35 mm DIN rail (also known as DIN 3) or flat surfaces.

For technical drawings and 3-D models, click on a part number.

Attach these relays to a flat surface using the mounting hole. They have no moving parts, so compared to mechanical switches, they require less maintenance, last longer, and are quieter.

Switches with a potentiometer (variable switch) allow you to adjust the delay within the range.

For technical drawings and 3-D models, click on a part number.

Mount these timer relays directly to 35 mm DIN rail (also known as DIN 3 rail) for fast installation. Unlike mechanical relays, they have no moving parts, so they require less maintenance and last longer, are quieter, and switch faster. After selecting a timing range, use the knob to adjust the trip time within the timing range.

Get a variety of timing functions in a single relay. All relays plug into relay sockets (sold separately) for fast installation and replacement.

Relay socket/panel mount relays require a mounting bracket (sold separately) to mount in a panel cutout.

Relay sockets mount to 35 mm DIN rail (also known as DIN 3 rail) or can be mounted to a flat surface.

Install these relays in a panel cutout or plug them into a relay socket. Unlike mechanical relays, these solid state relays have no moving parts, so they require less maintenance and last longer, are quieter, and switch faster. They give you a variety of timing functions in one relay.

Single-circuit relays give you additional flexibility—they have two types of delayed switch-off (delay-on-break) functions and two types of signal on/off delay functions.

Relay sockets (sold separately) mount to 35 mm DIN rail (also known as DIN 3 rail) for fast installation. They also mount to flat surfaces.

Mounting brackets (sold separately) are required to mount relays into a panel cutout.