Rod Supports | McMaster-Carr

Filter by

Material

Oil-Embedded Bronze

Stainless Steel

System of Measurement

Thread Size

Shank Thread Size

ID

Rod End Type

Ball Joint Linkage

Shank Gender

Shaft Diameter

Shank Center Length

Overall Length

Length

Overall Thickness

Shank Thread Direction

Thread Direction

Right Hand and Left Hand

OD

11/16" to 1 5/16"

Overall Width

Gender

Shank Thread Length

Diameter

Shape

U.S.–Mexico–Canada Agreement (USMCA) Qualifying

REACH

RoHS

Compliant with Exemptions

DFARS Specialty Metals

Export Control Classification Number (ECCN)

Shank Threading

Partially Threaded

How can we improve?

3,165 Products

Linear Shaft Supports

Easy-Access Base-Mount Linear Shaft Supports

Easy-Access Base-Mount Linear Shaft Supports

The top lifts off to let you access the shaft without needing to remove it

Base-Mount Linear Shaft Supports

Base-Mount Linear Shaft Supports

Slide the shaft in to install, then tighten to secure

Easy-Access Flange-Mount Linear Shaft Supports

Easy-Access Flange-Mount Linear Shaft Supports

The removable collar allows access to the shaft without unbolting the flange

Flange-Mount Linear Shaft Supports

Flange-Mount Linear Shaft Supports

Hold linear shafts perpendicular to the mounting surface

Linear Shaft Support Rails

Linear Shaft Support Rails

Position shafts an inch or two off the ground to maintain bearing and part clearance

Base-Mount Dual Linear Shaft Supports

Base-Mount Dual Linear Shaft Supports

Secure two shafts parallel to each other for smooth movement that doesn’t bind

Low-Profile Linear Shaft Support Rails

One-third the height of standard rails for shaft support in low vertical clearance

Machinable Easy-Access Base-Mount Linear Shaft Supports

Machinable Easy-Access Base-Mount Linear Shaft Supports

Create a support that fits the dimensions of your shaft to brace it on a flat surface

Other Products

Threaded Rod Mounts

Threaded Rod Mounts

Hang threaded rod from ceilings, walls, beams, and joists

Rod Ends

Use with connecting rods to support loads and control steering, tensioning, or pivoting motion

Linear Shafts

Pair with linear bearings and shaft supports to create smooth, precise motion

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

Rod End Seals

Keep dirt out and lubrication in to extend the life of rod ends

Seismic Bracing Mounts

Seismic Bracing Mounts

Bolster threaded-rod hangers and allow pipe systems to sway during earthquakes

Railing Clamps

Clamp onto metal tubes to hang lighting fixtures, threaded rod, and equipment

Rod End Inserts

Rod End Inserts

Attach to rod ends to increase the amount of misalignment they can handle

Beam Clamps

Secure lines of pipe and duct, overhead equipment, and lighting fixtures to beam flanges

Rod End Nuts

Attach to rods, pipe, and tubing to make pivot and hinge points

Shelf Brackets

Mount and support shelves

Vibration-Damping Hangers

Vibration-Damping Hangers

Reduce vibration and noise in suspended equipment, such as air-handling units, pipe, and duct

Strut Channel Framing and Fittings

Strut Channel Framing and Fittings

Secure fittings in the U-shaped channel to route conduit and pipe or build other structures

Swivel Joints

Handle shaft misalignment where ball joint rod ends won’t fit; also known as spherical bearings

Gas Spring End Fittings

Gas Spring End Fittings

Connect gas springs to mounting studs and brackets

Threaded Rod Anchors

Threaded Rod Anchors

Install directly into a flat surface for more holding power than threaded rod mounts

Eye Nuts

Pair with bolts or threaded rod to lift and hang components

Threaded Rod Hanger Beams

Threaded Rod Hanger Beams

Mount across roof joists to hang threaded rod and route pipe and duct in areas with no anchor point

Hydraulic Cylinder Mounts

Hydraulic Cylinder Mounts

Restrain cylinders and secure loads to the end of the rod

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)