Use these general purpose shafts with bearings, sprockets, and gears to transmit rotary motion.

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

In addition to diameter tolerances that are twice as tight as standard keyed shafts, these shafts include a traceable lot number and test report. Use them with machine keys to transmit torque to gears, sprockets, and other power transmission components.

Mount the flange to a machine or wall to support idler sprockets and pulleys in tensioning applications. They include washers and a nut to position your component and hold it in place.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

With a gear-shaped profile on one end, these shafts transmit high rotational loads—good for hydraulic systems, machine tools, and other high-torque applications. Compared to keyed shafts, they last longer, handle higher torque, and do not require as tight of a fit.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

Replace worn shafts in two-piece support-rail shaft systems, or mate with a support rail to create your own. The tapped mounting holes match those on our Support Rails.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

These rollers have diameters 1 3/4" and below.

Choose the width you need from 6" to 60" in 1/16" increments.

Choose the width you need from 6" to 60" in 1/16" increments.

Rollers have a standard 1.9" diameter to fit most roller conveyors.

Choose the width you need from 6" to 60" in 1/16" increments.

Choose the width you need from 6" to 60" in 1/16" increments.

Rubber-covered axles eliminate metal-to-metal contact to prevent frame wear and reduce noise.

Rollers are made from thick, 12-ga. steel so they're less likely to dent than standard 16-ga. rollers.

Rollers move in one direction so they won't roll back when idle, keeping packages in place.

Rollers have a standard 1.9" diameter to fit most roller conveyors.

" Rollers are grooved to accommodate round belts on line-shaft conveyors."

Rollers are tapered for use on curved conveyor sections.

Replace rollers on a chain-driven conveyor.

Use these bearings to replace worn and damaged bearings or press-fit them into tubing or pipe create a roller. All have a hex-shaped axle.

Sleeve bearings ride directly on the axle and have no moving parts to wear out.

Lock multiple spools together to increase drive power.

Covers fit loosely over the roller to allow packages to accumulate. Rollers can continue spinning inside the cover without causing damage to packages.

Mount to a conveyor frame to recondition a worn hex axle hole or to convert a round axle hole to a hex axle hole.

These urethane rollers are nonmarring and wear resistant.