Designed to rest on a work surface, these conveyors have two sets of axle holes so you can position the conveying surface 1/8" above the frame or 3/4" below the frame (position below to use the frame as a guide rail).

Galvanized steel conveyors are stronger than aluminum and have some corrosion resistance. Aluminum conveyors are lightweight and corrosion resistant.

Note: Capacities are based on an evenly distributed load. The length of the material you're conveying should be at least three times the roller spacing.

For technical drawings and 3-D models, click on a part number.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Rollers with seal have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Because they never need to be relubricated, these rollers are a good choice for hard-to-reach places. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to block dirt and contamination.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

For technical drawings and 3-D models, click on a part number.

With a double row of cylindrical roller bearings, these rollers provide the highest combination of speed and dynamic radial load ratings of any threaded track roller we offer. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers are permanently lubricated.

Crowned rollers have a slight curve, invisible to the naked eye, which helps them stay centered on surfaces that are slightly misaligned or not perfectly flat.

Rollers with seal have an end seal to protect the rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

The soft rubber or plastic surface on these rollers creates less noise than the metal surfaces found on other track rollers. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

Urethane-coated rollers provide better traction and abrasion resistance than nylon-coated rollers.

For technical drawings and 3-D models, click on a part number.

Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Secure the stud with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

For technical drawings and 3-D models, click on a part number.

Lubricated with graphite, these rollers can handle temperatures from -450° to 750° F—the widest temperature range of any track roller in our offering. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

These rollers are rated to handle radial and thrust (top and side) loads simultaneously. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers are permanently lubricated and have end seals to retain lubricant and protect rolling elements from dirt and contamination.

303 stainless steel rollers are more corrosion resistant than 440C stainless steel rollers.

For technical drawings and 3-D models, click on a part number.

With dry-running PTFE sleeve bearings, these rollers don’t require lubricant. They’re also fully submersible, nonsparking, and lightweight. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.

440C stainless steel rollers offer better corrosion resistance than chrome-plated steel rollers.

For technical drawings and 3-D models, click on a part number.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Lubricate rollers through a hole and groove in the inner ring.

Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.

Rollers with seal have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Lubricate rollers through a hole and groove in the inner ring. Rollers have end seals to protect rolling elements from dirt and contamination.

For technical drawings and 3-D models, click on a part number.

Made of neoprene rubber, these rollers resist oil, flames, gasoline, and weather. Also known as contact wheels and feed rollers, they have tapped hubs that allow you to mount them onto a shaft or stud to transmit power.

For technical drawings and 3-D models, click on a part number.

The surface of these rollers is molded to a ±0.003" tolerance to provide more consistent surface contact. Also known as contact wheels and feed rollers, they have tapped hubs that allow you to mount them onto a shaft or stud to transmit power. The urethane surface is nonmarring and wear resistant.

For technical drawings and 3-D models, click on a part number.

Install these rollers without the need for set screws or keyways. With a nonprotruding hub, they fit where standard drive rollers can’t. Also known as contact wheels and feed rollers, drive rollers spin in unison with shaft or stud to transmit power. The neoprene surface resists oil, flames, gasoline, and weather.

For technical drawings and 3-D models, click on a part number.

The mounting holes on these rollers are tapped directly through the roller’s surface so you can install them with set screws and still fit them into tight spots. Also known as contact wheels and feed rollers, drive rollers spin in unison with a shaft or stud to transmit power. The urethane surface is nonmarring and wear resistant.

For technical drawings and 3-D models, click on a part number.

Made of neoprene rubber, these rollers resist oil, flames, gasoline, and weather. Commonly found in conveyor systems and printing equipment, they spin freely on a shaft or stud to position and guide work.

For technical drawings and 3-D models, click on a part number.

These urethane rollers are nonmarring and wear resistant. Commonly found in conveyor systems and printing equipment, they spin freely on a shaft or stud to position and guide work.

For technical drawings and 3-D models, click on a part number.

A slippery UHMW polyethylene surface means these rollers won't stick to adjacent parts. Rollers are also highly corrosion resistant. Commonly found in conveyor systems and printing equipment, idler rollers spin freely on a shaft or stud to position and guide work.

Rollers with MDS-filled nylon bearing have a rigid, wear- and abrasion-resistant bearing for increased life over all-UHMW rollers.

For technical drawings and 3-D models, click on a part number.