System of Measurement System of Measurement |
|---|
|
Roller Diameter Roller Diameter | Show |
|---|
|
Roller Diameter Roller Diameter | Hide |
|---|
Roller Width Roller Width |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
Roller Style Roller Style |
|---|
 | Shaft Mount |
Track Roller Type Track Roller Type |
|---|
 | V-Groove |
For Load Direction For Load Direction |
|---|
 | Radial |
 | Combined Radial and Thrust |
 | Thrust |
Maximum Temperature Maximum Temperature |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Set Screw Included Set Screw Included |
|---|
|
Hardness Rating Hardness Rating |
|---|
|
Lubrication Lubrication |
|---|
|
About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
About Durometer
Durometer is the international standard for measuring the hardness of rubber, plastic, and most nonmetallic materials.
More
Abrasion-Resistant Keyed Drive Rollers
These urethane rollers are wear and chemical resistant. They’re also nonmarring. Use them with a keyed shaft to prevent slippage in high-torque applications. Also known as contact wheels and feed rollers, drive rollers spin in unison with a shaft or stud to transmit power.
For technical drawings and 3-D models, click on a part number.
Roller | Keyway | Set Screws | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | For Shaft Dia. | Wd. | Dp. | Overall Wd. | Dynamic Radial Load Capacity, lbs. | Shaft Mount Type | No. Required | Included | Temperature Range, °F | Durometer (Hardness Rating) | Each | |
Urethane Roller with Steel Hub | |||||||||||||
| 5" | 2" | 1/2" | 1/8" | 1/16" | 2 3/16" | 400 | Keyway, Set Screw | 2 | Yes | -20° to 120° | 85A (Hard) Red | 00000000 | 0000000 |
| 5" | 2" | 3/4" | 3/16" | 3/32" | 2 3/16" | 400 | Keyway, Set Screw | 2 | Yes | -20° to 120° | 85A (Hard) Red | 0000000 | 000000 |
Keyed Drive Rollers
For technical drawings and 3-D models, click on a part number.
Roller | Keyway | Set Screws | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | For Shaft Dia. | Wd. | Dp. | Overall Wd. | Dynamic Radial Load Capacity, lbs. | Shaft Mount Type | No. Required | Included | Temperature Range, ° F | Durometer (Hardness Rating) | Each | |
SBR Rubber Roller with Cast Iron Hub | |||||||||||||
| 5" | 2" | 3/4" | 3/16" | 3/32" | 2 3/16" | 400 | Keyway, Set Screw | 2 | Yes | 0° to 180° | 70A (Hard) Black | 00000000 | 0000000 |
Shaft-Mount V-Groove Track Rollers
Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end. Rollers are for use with Angle Rails for V-Groove Track Rollers. They handle radial and thrust (top and side) loads and work well in dirty environments because debris falls off the angled rail. All rollers are permanently lubricated.
Sealed rollers block out dust and other contaminants better than shielded rollers, but they hold more heat. Their seals also help retain lubricant.
For technical drawings and 3-D models, click on a part number.
Roller | Groove | Radial Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | For Shaft Dia. | Overall Wd. | Wd. | Dp. | Max. Speed, rpm | Static | Dynamic | Static Thrust Load Cap., lbs. | Max. Temp., °F | Bearing Type | Each | |
Steel V-Groove Rollers with Seal | |||||||||||||
| 5" | 2" | 1 1/8" | 2 1/16" | 1 1/2" | 3/4" | Not Rated | 27,200 | 17,000 | 13,000 | 225° | Tapered Roller | 0000000 | 0000000 |