Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made of 303/304 stainless steel, these mounts resist corrosion from water and most chemicals.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

An offset mounting hole allows for installation without moving your machine.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Cover the bottom of furniture legs.

Great for use outdoors, these feet are EPDM rubber, which withstands exposure to direct sunlight.

Screw these feet to the bottom of wood furniture legs.

A two-piece design simplifies installation and requires less clearance than one-piece mounts.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.

Bolt these mounts down to keep your equipment stationary.

A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.

A two-piece design makes these mounts easier to install than one-piece mounts.

These mounts withstand exposure to weather and resist oil, antifreeze, and other petroleum-based fluids.

Designed for tight spaces such as inside machinery, these mounts fit into a cutout, so they so they have a low top profile.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Spring action provides significant isolation of vibration and noise.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

Made of nitrile rubber, these mounts are oil resistant for use in compression load applications with punch presses, milling machines, grinders, and air compressors.

Able to shoulder up to 1,500 psi per mounting point, nitrile pads can support heavy machinery.

These soft pads work well for isolating vibration with light loads such as lab and testing equipment.

Great for use outdoors, these durable pads are neoprene rubber, which withstands exposure to direct sunlight.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist these bumpers into a threaded hole.

These bumpers withstand temperatures up to 300° F, which is twice as high as our other load rated bumpers. Use them in applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, these bumpers absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Twist them into a threaded hole.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

These bumpers are at a 90° angle to protect corners on equipment, walls, and docks from damage caused by carts, vehicles, and other moving objects. Install them with screws.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Select these bumpers for applications that require specific load capacities. All are reinforced with a base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines and conveyors. Mount these bumpers on a threaded stud.

Keep bumpers of various shapes, materials, and mounting styles on hand to solve whatever problems arise.

A magnetic base makes it easy to attach, move, and replace these bumpers on metal surfaces. Use them for guarding, aligning, and positioning parts.

Slide these feet on ladder legs to add slip resistance.

Fittings come in two pieces to wrap around rails, so you can quickly modify existing structures without disassembling. Use clamp-on framing and fittings to form temporary partitions, modular conveyors, and workstations.