A scaled-down version of standard screwdrivers, these tools are shorter, slimmer, and easy to take with you.

Sets include an assortment of drivers with a cushioned grip that provides comfort and some slip resistance.

These assorted drivers have bright-colored handles to stand out so they're less likely to be misplaced.

The assorted drivers in these sets have a shaft that extends through the handle and a steel end cap, which provide the strength to absorb hammer blows.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

The assorted drivers in these sets have a holding mechanism at the tip that ensures the screw won’t slip off.

Sets include an assortment of stainless steel drivers, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

These assorted screwdrivers are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Insert a bit into the shaft and a magnet holds it in place.

Drive screws four times faster than ratcheting alone. Grip the speed housing at the base of the shaft with one hand while turning the handle with the other. A magnet at the end of the shaft holds bits in place.

LEDs light the tip so you can use these tools in dark areas.

Press down on the handle’s collar to either adjust the shaft length or remove the shaft and replace it for a different tip. Sets include a handle and multiple reversible shafts.

The ball-end tip allows angled entry to turn screws in hard-to-reach areas. These tools are a scaled-down version of standard changeable-shaft screwdrivers, They're shorter, slimmer, and easy to take with you. Remove and replace the shaft to change the tip size.

Bits have a different tip at each end and snap into the shaft, which is also a nutdriver.

Mount the magnetic backing to walls, cabinets, and other steel surfaces. Magnetic slots secure your screwdrivers.

Position these low-profile rails to accommodate screwdrivers of any length.

Sets include an assortment of nutdrivers.

Press down on the handle’s collar to adjust the shaft length or remove and replace the shaft to change sizes. Sets include a handle and multiple shafts.

The assorted drivers in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. They are tested to 1,000 volts to meet ASTM and IEC standards.

Sets include an assortment of drivers with a tip that can be replaced when it becomes worn. Press the rotating end cap on the handle with your palm to apply constant pressure to small fasteners while turning the body of the screwdriver with your fingertips.

A magnetized tip holds the screw in place. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

The handle on these assorted ESD-safe screwdrivers drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include an assortment of drivers that allow you to apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

Also known as Bristol bits, these have a knurled-end shank that allows finger tightening. They can also be used with the included screwdriver.

These bits are also known as nut setters.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Grip the indentations on the head of tri-groove fasteners.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

Also known as Robertson bits these are designed for screws with a square recess in the head.

Mount the magnetic base to walls, cabinets, and other steel surfaces.

Keep these caddies in your tool drawer or take them with you.

The extra-short leg of these keys fits in tight spaces other tools can't and the long-leg ball end allows angled entry to turn screws in hard-to-reach areas.

These assorted keys have a ball end that allows angled entry to turn screws in hard-to-reach areas. The bright finish makes them easy to see and less likely to be misplaced.

These assorted keys have a bright finish that's easy to see, so they’re less likely to be misplaced. They turn fasteners from either end and reach into tight spots.

When a standard-tip key can't make good contact with the recess, a ball end allows angled entry to turn screws in hard-to-reach places. These keys have a zinc coating that resists salt-spray exposure.

These assorted keys have a detent that grips inside the recess to ensure screws won’t fall off. The ball end allows angled entry to drive fasteners in hard-to-reach areas.

The assorted tools in these sets have a flexible joint that provides access to fasteners in hard-to-reach areas.

Sets include an assortment of stainless steel keys with a ball end that allows angled entry to turn screws in hard-to-reach areas. Use a stainless steel L-key to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

These plastic organizers store keys in slots marked with the size.

Set includes a handle and six shafts. Remove and replace the shaft to use a different size or drive style.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

Sets include an assortment of short keys that fit in tight spaces where others can't.

The economical choice, these sets include an assortment of keys with a simple loop handle. The long shaft reaches into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

The assorted keys in these sets have a long shaft for more reach and a short shaft for more torque when turning fasteners.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

Select any key without unfolding the others in the set. The assorted keys turn multiple fastener sizes.

Bright-colored handles make these tools stand out, so they’re less likely to be misplaced. Sets include an assortment of keys for turning multiple fastener sizes.

Sets include an assortment of screw starters for gripping and turning screws that are too small to hold by hand or located in hard-to-reach spots.

Extra-long bits allow access to hard-to-reach fasteners.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

With sizes from EP10 to EP24, these sets have the sockets you need to install and remove a wide range of External Torx-Plus fasteners. Pair them with a square drive tool, such as a socket wrench, to deliver high levels of torque without slipping.

The handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Also known as ESD-safe screwdrivers and nutdrivers.

Also known as jewelers' screwdrivers.