Plastic screws are chemical and oil resistant, nonconductive, and lightweight.

Made from nylon, these metric pan head screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Reliable in harsh environments up to 500° F, PEEK screws withstand acids, bases, and salt solutions. They are chemical and oil resistant, nonconductive, and lightweight.

Made from polycarbonate, these metric pan head screws resist breaking in high-impact applications. They are chemical and oil resistant, nonconductive, and lightweight.

Made from nylon, these metric screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

These metric PTFE screws withstand harsh chemicals and temperatures from -100° F to 500° F. They are nonconductive, lightweight, and resist wear due to their slippery surface.

Nylon screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Made from nylon, these screws are chemical and oil resistant, nonconductive, and lightweight.

Plastic screws are chemical and oil resistant, nonconductive, and lightweight.

These metric screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

These metric polycarbonate screws resist breaking in high-impact applications better than other plastic screws. All are chemical and oil resistant, nonconductive, and lightweight.

These screws are more reliable in high-stress, high-temperature environments than other plastic screws. They withstand water, steam, and temperatures up to 500° F.

These nylon set screws are chemical resistant, lightweight, and nonconductive. The tip makes good contact on flat surfaces and allows you to make frequent adjustments with minimal surface damage.

Often used to secure gears and pulleys to shafts, these metric nylon set screws are lightweight and won’t carry an electrical current.

Stronger than standard nylon, these thumb screws are chemical resistant, nonconductive, and lightweight. They have a raised head that makes them easy to grip.

A thin head allows these thumb screws to be used in low-clearance applications.

Plastic binding barrels and caps are chemical resistant, nonconductive, and lightweight.

These rounded head nuts can be riveted into thin panels for a flush fit. They can be mounted without spaces between the panels. A quarter-turn locks and releases access panels, doors, and covers.

Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

These anchors are also known as drive rivets. To install, hammer the pin into the body. Pry out the pin to remove.

High-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed.

These anchors fit a range of sheet metal and wood screw sizes since they form their own threads when installed.

Easy to install, tap these anchors in like a nail—no drilled hole required.

Mount these knobs into a threaded hole. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A rubber coating provides a comfortable grip to position, tighten, and hold fixtures, equipment, and machinery. Mount these knobs into a threaded hole.

Knobs have left-hand threads; they're used in applications where counterclockwise motion can loosen common right-hand threads. Mount them into a threaded hole to position, tighten, and hold fixtures, equipment, and machinery.

Never lose these knobs—tether them to equipment to keep them where you need them. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Keep a convenient selection of knobs on hand. To build a custom knob or thumb screw, pair one of these knobs with a socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Mount these knobs into a threaded hole. Turn the knob to move the stud 0.005" per graduation and make precise adjustments.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Also known as nut eyebolts, these are designed for through-hole applications.

Conceal and protect the tops of socket head or button head screws.

A one-piece hinged design allows frequent access to screw heads without misplacing the top. To conceal and protect the entire screw head, insert your screw through the hole in the base and flip the hinged top over.