Use these general purpose 18-8 stainless steel screws for a variety of fastening applications. They have good chemical resistance.

Nearly as strong as steel, these stainless steel screws won’t rust in outdoor, washdown, and other corrosive environments. With half the height of a standard socket head, these low-profile screws fit in tight spaces.

316 stainless steel screws resist corrosion from chemicals and salt water better than 18-8 stainless steel screws. They may be mildly magnetic.

Made from 18-8 stainless steel, these metric pan head screws have good chemical resistance and may be mildly magnetic.

A zinc plating makes these metric pan head screws corrosion resistant in wet environments.

Made from 18-8 stainless steel, these metric screws have good chemical resistance and may be mildly magnetic. The extra-wide truss head distributes holding pressure to reduce the likelihood of crushing thin material.

Good for use outdoors and in washdown environments, these metric 18-8 stainless steel screws are more corrosion resistant than steel and nearly as strong. Their pan-shaped head sits nearly flat on the fastened surface, so there’s no need to countersink a hole.

Made from brass, these metric pan head screws are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

More corrosion resistant than 18-8 stainless steel screws, these screws have excellent resistance to chemicals and salt water.

18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. A Torx drive has more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

These metric 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic. Torx drives have more points of contact than other drives, allowing you to tighten the screw without damaging the recess.

Made from stainless steel, these metric screws have good chemical resistance and may be mildly magnetic. The washer has sharp internal teeth that dig into surfaces to resist large amounts of vibration while the smooth outside edge provides a finished look. Also known as Sems screws, the washer rotates freely but is permanently attached.

These metric 18-8 stainless steel screws have good chemical resistance and may be mildly magnetic.

More corrosion resistant than 18-8 stainless steel screws, these metric screws have excellent resistance to chemicals and salt water.

These metric screws have a decorative, domed head that sits above the surface when installed.

Angled under the head, these metric screws fit in countersunk holes and sit flush with the surface of your part.

These metric alloy-steel screws are twice as strong as standard steel Torx flat head screws.

These metric screws have a triangular shank that presses tightly as it forms threads, so screws resist loosening in soft metals such as brass, aluminum, and copper.

These metric set screws have good chemical resistance.

Made from alloy steel, these metric set screws have a thin edge that digs into hard surfaces for a secure hold. They have a nylon locking patch that grips threads to resist loosening.

These metric set screws are vented to allow fluid and gas to pass through.

Good for humid, damp, and washdown areas, these metric 18-8 stainless steel set screws are more corrosion resistant than alloy steel set screws and nearly as strong. Their flat tip holds tightly on flat surfaces without damaging them, even when making frequent adjustments.

Made of brass, these metric set screws are electrically conductive, nonmagnetic, and have mild corrosion resistance in wet areas. Their flat tip holds tightly on flat surfaces without damaging them, even when making frequent adjustments.

Fine threads give you precise control. A rolling ball allows for slight adjustments without loosening the screw.

Available in metric sizes, these 18-8 stainless steel threaded rods have good chemical resistance.

These metric brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

18-8 stainless steel studs have good chemical resistance.

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Twist these adapters onto female metric threads to change pitch or switch thread sizes.