McMaster-Carr logo
    Filter by
    System of Measurement
    Thread Pitch
    Industrial Info Snippet
    Attribute Image
    Thread Type
    Thread Direction
    Thread Fit
    Industrial Info Snippet
    Thread Spacing
    Industrial Info Snippet
    DFARS Specialty Metals
    Industrial Info Compare
    Export Control Classification Number (ECCN)
    Base Diameter
    Specifications Met
    Hole Diameter
    Drill Bit Size
    Attribute Image
    For Minimum Length Between Hole Center and Sheet Edge
    Drill Bit Decimal Size Equivalent
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    27 Products

    Threaded Rods

    Anchor, connect, or hang components in a wide variety of applications, from mounting I-beams to suspending light fixtures.
    Low-Strength Steel
    Image of Product. Front orientation. Threaded Rods. Threaded Rods.
    With a tensile strength of 50,000 psi or 60,000 psi, these rods are often used to suspend light fixtures, cable trays, and conduit from ceilings. They're about half the strength of medium-strength steel rods. To avoid stripped threads during installation, make sure your nuts are also low-strength steel.
    Zinc-Plated Steel—The most common choice for areas with occasional exposure to moisture.
    Lg.
    Tensile Strength,
    psi
    Hardness
    Specs.
    Met
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
     
    M2.5 × 0.45 mm
    50 mm50,000Rockwell B49DIN 9761000000000000000
    300 mm50,000Rockwell B49DIN 976100000000000000
    1 m50,000Rockwell B49DIN 976100000000000000
     
    Stainless Steel
    Image of Product. Front orientation. Threaded Rods. Threaded Rods.
    More corrosion resistant than steel rods and comparable in strength to low-strength steel.
    18-8 Stainless Steel—The choice for wet and outdoor environments, these rods resist rust. However, they won't hold up to the harsh chemicals that 316 stainless steel can.
    Super-Corrosion-Resistant 316 Stainless Steel—Superior to 18-8 stainless steel, these rods won't degrade when exposed to harsh weather, salt water, and most chemicals.
    Lg.
    Tensile Strength,
    psi
    Hardness
    Specs.
    Met
    Pkg.
    Qty.
    Pkg.
    18-8 Stainless Steel
     
    M2.5 × 0.45 mm
    12 mm70,000Not RatedDIN 97610000000000000000
    16 mm70,000Not RatedDIN 9761000000000000000
    20 mm70,000Not RatedDIN 9761000000000000000
    25 mm70,000Not RatedDIN 9761000000000000000
    50 mm70,000Not RatedDIN 9761000000000000000
    300 mm70,000Not RatedDIN 97610000000000000
    500 mm70,000Not RatedDIN 97610000000000000
    1 m70,000Not RatedDIN 976100000000000000
    2 m70,000Not RatedDIN 976100000000000000
     
    Super-Corrosion-Resistant 316 Stainless Steel
     
    M2.5 × 0.45 mm
    12 mm70,000Not RatedDIN 97650000000000000
    25 mm70,000Not RatedDIN 976500000000000000
    300 mm70,000Not RatedDIN 97610000000000000
    500 mm70,000Not RatedDIN 97610000000000000
    1 m70,000Not RatedDIN 976100000000000000
     
    Brass
    Image of Product. Front orientation. Threaded Rods. Threaded Rods.
    Brass—Conductive and nonmagnetic, brass rods are commonly used to secure electrical equipment, such as circuit board assemblies and mounting brackets, inside enclosures.
    Lg.,
    m
    Tensile Strength,
    psi
    Hardness
    Specs.
    Met
    Each
    Brass
     
    M2.5 × 0.45 mm
    150,000Rockwell B55DIN 976000000000000000
     

    Press-Fit Studs

    Image of Product. Front orientation. Studs. Press-Fit Studs.
    Press these studs into a drilled or punched hole with an arbor press or similar pressure tool. Also known as self-clinching studs, ribs under the head hold the stud firmly in place. Length listed is overall length.
    Zinc-Plated Steel—The most common choice for areas with occasional exposure to moisture.
    18-8 Stainless Steel—The choice for wet and outdoor environments, these studs resist rust. However, they won't hold up to the harsh chemicals that 316 stainless steel can.
    Lg.,
    mm
    PEM® Part
    No.
    Thread
    Lg., mm
    For Min. Material
    Thk., mm
    For Min. Lg. Between Hole
    Ctr. and Sheet Edge, mm
    For Hole
    Dia., mm
    Hole Size Tolerance,
    mm
    Drill Bit
    Size, mm
    Base Dia.,
    mm
    Tensile
    Strength
    Hardness
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Steel
     
    M2.5 × 0.45 mm
    6FH-M2.5-641.0005.52.50.000 to 0.0840 Ga.
    		4.5Not RatedNot Rated5000000000000000
    10FH-M2.5-1081.0005.52.50.000 to 0.0840 Ga.
    		4.5Not RatedNot Rated500000000000000
    15FH-M2.5-15131.0005.52.50.000 to 0.0840 Ga.
    		4.5Not RatedNot Rated500000000000000
    18FH-M2.5-18161.0005.52.50.000 to 0.0840 Ga.
    		4.5Not RatedNot Rated250000000000000
     
    18-8 Stainless Steel
     
    M2.5 × 0.45 mm
    6FHS-M2.5-641.00052.50.000 to 0.082.53.7Not RatedNot Rated250000000000000
    8FHS-M2.5-861.00052.50.000 to 0.082.53.7Not RatedNot Rated250000000000000
    10FHS-M2.5-1081.00052.50.000 to 0.082.53.7Not RatedNot Rated250000000000000
    12FHS-M2.5-12101.00052.50.000 to 0.082.53.7Not RatedNot Rated250000000000000
    15FHS-M2.5-15131.00052.50.000 to 0.082.53.7Not RatedNot Rated250000000000000
     
    back to top