Keep your hand away from the material being cut.

The handles are angled 90° from the blade so you can cut material from directly above tight spaces.

This cutter has two blades that cut a 13/64" wide strip—peel it back for smooth edges with little distortion.

Replace blades as they wear. These cutters are also known as tinners' snips.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Make cuts in metal up to 1/32" thick with these compact cutters.

Make round, square, and irregular-shaped holes with this punch-style hole cutter.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Turn your workpiece while cutting to create curves and complex shapes.

These air-powered cutters include a semi-square blade for no-fray cuts.

Leave clean cut edges in a variety of pliable materials.

Turn the handle to make quick and accurate circular cuts.

Ensure precise cuts with a measuring scale and adjustable blade depth.

Make repeated cuts in hard materials with cutters that mount for stability and provides extra leverage.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

With a short-nosed jaw, these cutters force the material being cut deeper into the jaw for maximum leverage. The short jaw also allows you to cut one side of a chain link or padlock hasp without hitting the other side.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

Cut thin, hard wire with these small cutters.

Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.

Cutters have double hinge that provides high cutting force with low gripping pressure.

Keep your hands in a comfortable position so you can apply more force for cutting.

Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.

Make clean cuts on threaded rod with the pull of a trigger.

An alternative to hacksaws and bandsaws, these cutters use leverage to cut rods cleanly in a single stroke.

Cut armored cable such as BX, HCF, and MC and flexible metal conduit.

Minimize wire distortion when cutting 11/16" diameter and larger aluminum and copper power and communication cable.

Jaws ratchet to increase cutting pressure as you open and close the handles.

Fit this compact cutter into your pocket or tool belt.

Cut plastic and rubber pipe, tubing, and hose.

Titanium is bonded over stainless steel for blades with a sharp, long-lasting cutting edge that's three times harder than uncoated stainless steel.

Made of aluminum-bronze that is FM approved, these scissors satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Blades are titanium bonded over stainless steel for a sharp, long-lasting cutting edge, and they have narrow, sharp tips for fine cutting and trimming.

For extra leverage to cut through tough materials such as leather, rope, and thick cardboard, these scissors have long handles and short blades.

Prevent snags and injury with the rounded points on these small scissors.

After each cut, the jaws spring open to make continuous cutting easy.

Cut and strip wire in tight spaces with the compact tips on these scissors.

Insulated handles protect against shock from accidental contact with live electrical circuits. These scissors are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Make oblong holes in fabric, leather, and rubber. Also known as arch punches.

Attach two punch heads to the handle at the same time to punch a gasket or washer in a single strike.

Use these one-piece tools to make round holes up to 1 3/4" dia.

For accurate punching of inner and outer holes, these sets come with pilots that attach to the outer hole punch.

Sets include common ID and OD sizes to create gaskets and washers in two strikes.

Cut through hundreds of sheets at a time.

A hand clamp exerts extra pressure for improved cutting accuracy. These paper cutters have a guard that completely covers the blade to prevent accidents.