Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Replace a damaged bowl on your Norgren modular compressed air lubricator.

Replace a damaged bowl, or change the bowl material on your ARO modular compressed air lubricator.

Replace a damaged bowl, or change the bowl material on your ASCO Numatics modular compressed air lubricator.

Replace a cracked or lost sight dome on your SMC modular compressed air lubricator.

Replace a cracked or lost sight dome on your Wilkerson modular compressed air lubricator.

Install one of these lubricators at the point of use to lubricate your air-powered hand tools.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Norgren filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Festo filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.

With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Connect a tube fitting and tubing to the dispenser outlet to access hard-to-reach lubrication points.

Serve multiple lubrication points from a single location.

Serve multiple lubrication points from a single location.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

For use in clean environments, these oil reservoirs have multiple air vents that keep pressure balanced.

Deliver an equal amount of oil to multiple lubrication points at once.

A solenoid automatically starts and stops flow to a single lubrication point to dispense lubricant while equipment is running.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Flip the lever to start and stop flow.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

These dispensers have an opening for filling without removing the nozzle.

Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

Use suction to remove old lubricant from gear boxes and transmissions.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Measure oil as it's dispensed.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

These dispensers come packed with grease, eliminating the mess of filling. Turn the dial to adjust flow rate.

Tighten the cover to dispense grease.

Useful in remote areas without access to air or electrical power.

Apply lubricant to gear racks with a 14 1/2° pressure angle and a pitch of 16.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Dispense from grease guns into grease fittings and bare lubrication points.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

These rigid nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Mount holders in convenient locations to keep grease guns within reach.

Lubricate standard grease fittings in hard-to-reach areas. Extensions have a quick-disconnect fitting that snaps into your dispensing tip for standard grease fittings.

Convert dispensing tips with male threads into quick-disconnect couplings.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

Dispense small amounts of grease with one of these compact guns.

Deliver small amounts of grease with only a light push against the lubrication point.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

Dispense grease with the highest-pressure-rated gun we offer.

Be sure you’re using the right grease—this gun has a clear barrel for identification at a glance.

Dispense small amounts of grease with this compact gun.

More portable than air-powered options, these guns operate on a rechargeable battery.

Replace the dispensing tip on your filler pump.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

Dispense grease using compressed air.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Kits contain lengths of hose, nozzles, valves, and caps.

Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

Use with Snap-Loc hose to assemble and disassemble components.

Swivel the ball-socket connections to position these arms and then lock them in place.

These dispensers have a reservoir and controls for coolant flow.

Draw coolant from your existing tank.

Deliver a small, controlled amount of coolant to a workpiece.

The most versatile of our machine-mount coolant nozzles, these adjust from a fine mist to a direct stream and can deliver coolant in any direction. Max. pressure is 100 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Assortments contain straight, 45° elbow, and 90° elbow fittings.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Use these fittings in tight spaces where protruding fittings won't work.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. They're also known as hydraulic grease fittings.

Use these fittings in tight spaces where protruding fittings won't work. Drive them into unthreaded holes.