0.007" Shims | McMaster-Carr

Boost bearing efficiency and lifespan. Often used on motor shafts, these shims evenly distribute the load between multiple bearings by creating space between their outer rings. This prevents excessive pressure on any single bearing, maintaining proper alignment for smooth operation and reduced wear.

You can stack multiple shims to achieve your exact thickness, but stacking more than four may cause them to shift. Remember, fewer shims are better, so a couple of thicker shims are more stable than a bunch of thin shims.

18-8 Stainless Steel—The choice for wet and outdoor environments, these shims resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.

Highly-Corrosion-Resistant 316 Stainless Steel—Superior to 18-8 stainless steel, these shims won't degrade when exposed to harsh weather, salt water, and most chemicals.

Brass—With a warm, polished look, these shims are often chosen for their appearance. Similar to 18-8 stainless steel, brass is corrosion resistant enough to stand up to wet environments.

	For Bearing
	Trade No.	ID	OD	ID	ID Tolerance	OD	OD Tolerance	Min. Hardness	Thk.	Pkg. Qty.		Pkg.
18-8 Stainless Steel



		R0	3/64"	5/32"	0.088"	0" to 0.005"	0.153"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	000000


		R1	0.055"	3/16"	0.123"	0" to 0.005"	0.178"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000
		R1-4, R144	5/64", 1/8"	1/4"	0.167"	0" to 0.005"	0.248"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000
		R1-5, R2-5	3/32", 1/8"	5/16"	0.206"	0" to 0.005"	0.31"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000
		R2, R166	1/8", 3/16"	3/8"	0.253"	0" to 0.005"	0.373"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000
		R3, R188	3/16", 1/4"	1/2"	0.378"	0" to 0.005"	0.498"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000
		R4	1/4"	5/8"	0.503"	0" to 0.005"	0.623"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000
		R6	3/8"	7/8"	0.687"	0" to 0.005"	0.873"	-0.005" to 0"	Rockwell B70	0.007"	25	000000000	00000


		Highly-Corrosion-Resistant 316 Stainless Steel



				R1	0.055"	3/16"	0.123"	0" to 0.005"	0.178"	-0.005" to 0"	Rockwell B90	0.007"	10	000000000	00000


				R1-4, R144	5/64", 1/8"	1/4"	0.167"	0" to 0.005"	0.248"	-0.005" to 0"	Rockwell B90	0.007"	10	000000000	00000
				R1-5, R2-5	3/32", 1/8"	5/16"	0.206"	0" to 0.005"	0.31"	-0.005" to 0"	Rockwell B90	0.007"	10	000000000	00000
				R2, R166	1/8", 3/16"	3/8"	0.253"	0" to 0.005"	0.373"	-0.005" to 0"	Rockwell B90	0.007"	10	000000000	00000
				R3, R188	3/16", 1/4"	1/2"	0.378"	0" to 0.005"	0.498"	-0.005" to 0"	Rockwell B90	0.007"	10	000000000	00000
				R4	1/4"	5/8"	0.503"	0" to 0.005"	0.623"	-0.005" to 0"	Rockwell B90	0.007"	10	000000000	00000


				Brass



						R1	0.055"	3/16"	0.123"	0" to 0.005"	0.178"	-0.005" to 0"	Rockwell B70	0.007"	10	000000000	0000


						R1-4, R144	5/64", 1/8"	1/4"	0.167"	0" to 0.005"	0.248"	-0.005" to 0"	Rockwell B70	0.007"	10	000000000	0000
						R1-5, R2-5	3/32", 1/8"	5/16"	0.206"	0" to 0.005"	0.31"	-0.005" to 0"	Rockwell B70	0.007"	10	000000000	0000
						R2, R166	1/8", 3/16"	3/8"	0.253"	0" to 0.005"	0.373"	-0.005" to 0"	Rockwell B70	0.007"	10	000000000	0000
						R3, R188	3/16", 1/4"	1/2"	0.378"	0" to 0.005"	0.498"	-0.005" to 0"	Rockwell B70	0.007"	10	000000000	0000
						R4	1/4"	5/8"	0.503"	0" to 0.005"	0.623"	-0.005" to 0"	Rockwell B70	0.007"	10	000000000	0000

Shim Stock

Cut into custom shapes to create shims that suit your needs. With thickness tolerances as fine as a strand of hair, the shims will precisely align, space, and level components on dies, presses, and machinery.

18-8 Stainless Steel—The choice for wet and outdoor areas because it resists rust. However, it will corrode or pit when exposed to salt water and chemicals.

Highly-Corrosion-Resistant 316 Stainless Steel—Superior to 18-8 stainless steel, it won't degrade when exposed to harsh weather, salt water, and most chemicals.

High-Strength 17-7 PH Stainless Steel—Similar in strength to steel, it won’t rust in wet and outdoor areas but can’t withstand harsh chemicals like 316 stainless steel.

Carbon Steel—Best for dry areas since moisture will cause it to rust.

Stress-Resistant Spring Steel—Harder and holds its shape better than carbon steel. Use it for high-stress applications, such as leveling heavy machinery. It's best for dry areas since moisture will cause it to rust.

Painted Aluminum—An alternative to stainless steel for rust resistance but less hard so it may not retain its shape. One-third the weight of steel, it's often used in robotics and automation.

Brass—Picked for its warm, polished look. Similar to 18-8 stainless steel, it resists rusting in wet and outdoor areas.

Copper—A good conductor of heat, it’s often used to install heat sinks. As our softest metal, it prevents component damage but may not retain its shape as well as other metals.

Titanium—Grade 2 titanium, 99% pure, is often used in chemical-processing plants for its resistance to strong acids and other harsh chemicals. It has a high strength-to-weight ratio.

Ultra-Chemical-Resistant PTFE—The most chemical-resistant shim stock we offer, it stands up to the widest range of harsh acids, bases, solvents, and corrosive cleaners, even at temperatures up to 500° F. It also won't mar delicate surfaces.

Temper Rating—Choose half hard to create shims that you’ll need to bend or shape. Opt for full hard to make stronger shims that will maintain their shape under loads.

	Thk.	Thk. Tolerance	Temper Rating	Color	Type	Certificate Form	Specs. Met	Form	Pkg. Qty.		Pkg.
18-8 Stainless Steel







				6" Wide × 25" Long

				0.007"	-0.00035" to 0.00035"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Sheet	1	0000000	000000




						6" Wide × 50" Long

						0.007"	-0.0004" to 0.0004"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Roll	1	0000000	00000


						0.007"	-0.00035" to 0.00035"	1/2 Hard	—	Material Certificate	Paper	ASTM A666	Roll	1	0000000	00000




								6" Wide × 100" Long

								0.007"	-0.0004" to 0.0004"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Roll	1	00000000	00000




										8" Wide × 12" Long

										0.007"	-0.00035" to 0.00035"	1/2 Hard	—	Material Certificate	Paper	ASTM A666	Sheet	1	00000000	00000


										0.007"	-0.00035" to 0.00035"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Sheet	1	00000000	00000




												12" Wide × 50" Long

												0.007"	-0.0004" to 0.0004"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Roll	1	0000000	00000




														12" Wide × 100" Long

														0.007"	-0.0004" to 0.0004"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Roll	1	0000000	00000




																24" Wide × 24" Long

																0.007"	-0.00035" to 0.00035"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Sheet	1	00000000	00000




																		24" Wide × 50" Long

0.007"																		-0.0004" to 0.0004"	Full Hard	—	Material Certificate	Paper	ASTM A666, SAE AMS5906, SAE AMS5913	Sheet	1	0000000	00000


Highly-Corrosion-Resistant 316 Stainless Steel







																		6" Wide × 50" Long

				0.007"														-0.0005" to 0.0005"	—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Roll	1	00000000	00000




																		6" Wide × 100" Long

																		0.007"	-0.0005" to 0.0005"	—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Roll	1	00000000	00000




																		8" Wide × 12" Long

																		0.007"	-0.0005" to 0.0005"	—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Sheet	1	0000000	00000




																		12" Wide × 50" Long

																		0.007"	-0.0005" to 0.0005"	—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Roll	1	00000000	00000




																				12" Wide × 100" Long

										0.007"	-0.0005" to 0.0005"									—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Roll	1	00000000	000000




												24" Wide × 24" Long

												0.007"	-0.0005" to 0.0005"							—	—	Material Certificate	Paper	ASTM A240, ASTM A666, SAE AMS5507, SAE AMS5524	Sheet	1	0000000	00000




																				24" Wide × 50" Long

														0.007"	-0.0005" to 0.0005"					—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Roll	1	00000000	000000




																				24" Wide × 100" Long

																0.007"	-0.0005" to 0.0005"			—	—	Material Certificate	Paper	ASTM A240, SAE AMS5507, SAE AMS5524	Roll	1	00000000	000000


																High-Strength 17-7 PH Stainless Steel







		6" Wide × 50" Long

		0.007"	-0.00035" to 0.00035"																	Full Hard	—	Material Certificate	Paper	ASTM A693	Roll	1	0000000	00000


		Carbon Steel







																				6" Wide × 25" Long

																				0.007"	-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	ASTM A109	Sheet	1	00000000	0000




																				6" Wide × 50" Long

																				0.007"	-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	—	Roll	1	00000000	00000




																				6" Wide × 100" Long

																				0.007"	-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	—	Roll	1	00000000	00000




																				6" Wide × 180" Long

																				0.007"	-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	—	Roll	1	00000000	00000




																				8" Wide × 12" Long

																				0.007"	-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	ASTM A109	Sheet	5	00000000	00000




																				12" Wide × 120" Long

														0.007"						-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	—	Roll	1	00000000	00000




																				24" Wide × 24" Long

																				0.007"	-0.00075" to 0.00075"	Full Hard	—	Material Certificate	Paper	ASTM A109	Sheet	1	00000000	00000


																Stress-Resistant Spring Steel







																				6" Wide × 12" Long

		0.007"																		-0.0004" to 0.0004"	Full Hard	—	Material Certificate	Paper	ASTM A684, SAE AMS5122	Sheet	1	00000000	00000




				6" Wide × 25" Long

				0.007"	-0.0005" to 0.0005"															Full Hard	—	Material Certificate	Paper	ASTM A684, SAE AMS5122	Sheet	1	0000000	00000




																				6" Wide × 50" Long

						0.007"	-0.0004" to 0.0004"													Full Hard	—	Material Certificate	Paper	ASTM A682, ASTM A684, MIL-S-7947	Roll	1	0000000	00000




																				8" Wide × 12" Long

								0.007"	-0.0004" to 0.0004"											Full Hard	—	Material Certificate	Paper	ASTM A684, SAE AMS5122	Sheet	1	00000000	00000


								Painted Aluminum







																				6" Wide × 24" Long

																				0.007"	-0.0007" to 0.0007"	1/2 Hard to Full Hard	Aluminum	Material Certificate	Paper	—	Sheet	1	0000000	0000




																				12" Wide × 24" Long

																				0.007"	-0.0007" to 0.0007"	1/2 Hard to Full Hard	Aluminum	Material Certificate	Paper	—	Sheet	1	0000000	00000


												Brass







																				6" Wide × 50" Long

																				0.007"	-0.0007" to 0.0007"	1/2 Hard	—	Material Certificate	Paper	ASTM B36	Roll	1	00000000	00000




																				6" Wide × 60" Long

	0.007"																			-0.0007" to 0.0007"	1/2 Hard	—	Material Certificate	Paper	ASTM B36	Roll	1	0000000	00000




																				6" Wide × 100" Long

		0.007"	-0.0007" to 0.0007"																	1/2 Hard	—	Material Certificate	Paper	ASTM B36	Roll	1	0000000	00000




																				8" Wide × 12" Long

				0.007"	-0.0007" to 0.0007"															1/2 Hard	—	Material Certificate	Paper	ASTM B36	Sheet	1	00000000	00000


				Copper







																				6" Wide × 50" Long

																				0.007"	-0.0004" to 0.0004"	—	—	Material Certificate	Paper	ASTM B152	Roll	1	0000000	00000




																				6" Wide × 100" Long

																		0.007"		-0.0004" to 0.0004"	—	—	Material Certificate	Paper	ASTM B152	Roll	1	0000000	00000


																		Titanium







																				6" Wide × 50" Long

																				0.007"	-0.0007" to 0.0007"	—	—	Material Certificate	Paper	ASTM B265	Roll	1	0000000	000000




																				12" Wide × 50" Long

														0.007"						-0.0007" to 0.0007"	—	—	Material Certificate	Paper	ASTM B265	Roll	1	0000000	000000


														Ultra-Chemical-Resistant PTFE







																				8" Wide × 12" Long

	0.007"																			-0.0007" to 0.0007"	—	White	—	—	ASTM D3308, MIL-P-22241	Sheet	1	00000000	00000

Shims

With thickness tolerances as fine as a strand of hair, these shims precisely align, space, and level components on shafts, arbors, and machinery.

18-8 Stainless Steel—The choice for wet and outdoor environments, these shims resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.

Carbon Steel—Best for dry environments since moisture will cause these shims to rust.

	Thk.	Thk. Tolerance	ID Tolerance	OD Tolerance	Min. Hardness	Specs. Met	Pkg. Qty.		Pkg.
18-8 Stainless Steel







				1/4" ID × 3/8" OD

				0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	00000




						11/32" ID × 13/16" OD

						0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	0000




								3/8" ID × 5/8" OD

								0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	00000




										1/2" ID × 3/4" OD

										0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	00000




												5/8" ID × 1" OD

												0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	00000




														3/4" ID × 1 1/8" OD

														0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	00000




																7/8" ID × 1 3/8" OD

																0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	10	000000000	00000




																		1" ID × 1 1/2" OD

																		0.007"	-0.0007" to 0.0007"	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	5	000000000	00000




																				1 1/8" ID × 1 5/8" OD

0.007"	-0.0007" to 0.0007"																			0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	5	000000000	00000




		1 1/4" ID × 1 3/4" OD

		0.007"	-0.0007" to 0.0007"																	0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	5	000000000	0000




				1 3/8" ID × 1 7/8" OD

				0.007"	-0.0007" to 0.0007"															0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	5	000000000	00000




																				1 1/2" ID × 2 1/8" OD

						0.007"	-0.0007" to 0.0007"													0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	5	000000000	00000




																				1 3/4" ID × 2 3/4" OD

								0.007"	-0.0007" to 0.0007"											0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	5	000000000	00000




																				2" ID × 2 3/4" OD

										0.007"	-0.0007" to 0.0007"									0" to 0.011"	-0.002" to 0.002"	Rockwell B70	ASTM A240	1	000000000	0000


										Carbon Steel







																				1/4" ID × 3/8" OD

																				0.007"	-0.00075" to 0.00075"	0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				3/8" ID × 5/8" OD

																				0.007"	-0.00075" to 0.00075"	0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				1/2" ID × 3/4" OD

																				0.007"	-0.00075" to 0.00075"	0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




5/8" ID × 1" OD

0.007"	-0.00075" to 0.00075"																			0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				3/4" ID × 1 1/8" OD

		0.007"	-0.00075" to 0.00075"																	0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				7/8" ID × 1 3/8" OD

				0.007"	-0.00075" to 0.00075"															0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				1" ID × 1 1/2" OD

						0.007"	-0.00075" to 0.00075"													0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				1 1/8" ID × 1 5/8" OD

								0.007"	-0.00075" to 0.00075"											0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




																				1 1/4" ID × 1 3/4" OD

										0.007"										-0.00075" to 0.00075"	0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	0000




												1 3/8" ID × 1 7/8" OD

												0.007"	-0.00075" to 0.00075"							0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	00000




																				1 1/2" ID × 2 1/8" OD

														0.007"	-0.00075" to 0.00075"					0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	00000




																				1 3/4" ID × 2 3/4" OD

																0.007"	-0.00075" to 0.00075"			0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	00000




																				2" ID × 2 3/4" OD

																		0.007"	-0.00075" to 0.00075"	0" to 0.011"	-0.002" to 0.002"	Rockwell B65	—	10	00000000	00000

Adhesive-Back Shim Stock

Stick with confidence—a durable adhesive keeps this shim stock from sliding out of place. Cut the shim stock into custom shapes to create shims that suit your needs. With thickness tolerances as fine as a strand of hair, the shims will precisely align, space, and level components on dies, presses, and machinery.

18-8 Stainless Steel—The choice for wet and outdoor areas because it resists rust. However, it will corrode or pit when exposed to salt water and chemicals.

Highly-Corrosion-Resistant 316 Stainless Steel—Superior to 18-8 stainless steel, it won't degrade when exposed to harsh weather, salt water, and most chemicals.

Aluminum—An alternative to stainless steel for rust resistance but less hard so it may not retain its shape. One-third the weight of steel, it's often used in robotics and automation.

Brass—Picked for its warm, polished look. Similar to 18-8 stainless steel, it resists rusting in wet and outdoor areas.

Temper Rating—Choose half hard to create shims that you’ll need to bend or shape. Opt for full hard to make stronger shims that will maintain their shape under loads.

Certificates with a traceable lot number are available for these products. Download certificates from ORDER HISTORY after your order ships.

							Certificate
	Thk.	Thk. Tolerance	Material Thk.	Adhesive Thk.	Adhesive Type	Temper Rating	Type	Form	Specs. Met	Form		Each
18-8 Stainless Steel







				8" Wide × 12" Long

				0.007"	-0.00025" to 0.00025"	0.005"	0.002"	Acrylic	Full Hard	Material Certificate	Digital	ASTM A666	Sheet	00000000	000000


				Highly-Corrosion-Resistant 316 Stainless Steel







								8" Wide × 12" Long

								0.007"	-0.00025" to 0.00025"	0.005"	0.002"	Acrylic	—	Material Certificate	Digital	ASTM A666	Sheet	00000000	00000


								Aluminum







												6" Wide × 12" Long

												0.007"	-0.0005" to 0.0005"	0.005"	0.002"	Acrylic	—	Material Certificate	Digital	ASTM B479	Sheet	00000000	00000


												Brass







																8" Wide × 12" Long

																0.007"	-0.0005" to 0.0005"	0.005"	0.002"	Acrylic	1/2 Hard	Material Certificate	Digital	ASTM B36	Sheet	00000000	00000

Made-to-Order Shims

Image of Product. Front orientation. Shims. Sold Individually, Made-to-Order.

If you need a unique shim shape or size, we’ll precision cut it for you. With thickness tolerances as fine as a strand of hair, these shims precisely align, space, and level components on shafts, arbors, and machinery.

Send your dimensioned DWG, DXF, IGES, or STEP file to sales@mcmaster.com. Please leave at least _1/8" wall between shim edge and holes. Minimum hole size is _1/8". Shims should be no smaller than 1" × 1" square or 1" OD. Maximum shim dimension is the largest overall length, width, or diameter of your custom shim.

18-8 Stainless Steel—The choice for wet and outdoor environments, these shims resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.

Highly-Corrosion-Resistant 316 Stainless Steel—Superior to 18-8 stainless steel, these shims won't degrade when exposed to harsh weather, salt water, and most chemicals.

Carbon Steel—Best for dry environments since moisture will cause these shims to rust.

Material Certificate—Shims include a report with a traceable lot number.

						2" × 2" Maximum Shim Size			5" × 5" Maximum Shim Size			7" × 7" Maximum Shim Size			11" × 11" Maximum Shim Size			23" × 23" Maximum Shim Size
	Thk.	Thk. Tolerance	Min. Hardness	Certificate Type	Specs. Met	Pkg. Qty.		Pkg.	Pkg. Qty.		Pkg.	Pkg. Qty.		Pkg.	Pkg. Qty.		Pkg.	Pkg. Qty.		Pkg.
18-8 Stainless Steel



		0.007"	-0.00035" to 0.00035"	Rockwell C42	Material Certificate	ASTM A240	16	000000000	000000	4	000000000	000000	9	000000000	0000000	4	000000000	0000000	1	000000000	0000000


		Highly-Corrosion-Resistant 316 Stainless Steel



				0.007"	-0.00035" to 0.00035"	Not Rated	Material Certificate	ASTM A240, Fed. Spec. QQ-S-766	16	000000000	00000	4	000000000	00000	9	000000000	000000	4	000000000	000000	1	000000000	000000


				Carbon Steel



						0.007"	-0.00035" to 0.00035"	Rockwell B90	Material Certificate	ASTM A109, Fed. Spec. QQ-S-698	16	000000000	00000	4	000000000	00000	9	000000000	00000	4	000000000	00000	1	000000000	00000

Wave Spring Lock Washers

The wavy shape flexes like a spring to keep nuts and screws secure on slightly uneven surfaces. These washers add a small amount of tension to stop fasteners from backing out due to mild vibration. While they don't hold as well as other lock washers, they do grip slightly better than curved washers. They work best in electrical panels, light fixtures, and other light duty assemblies. Since these washers hold their shape when untightened, you can reuse them a handful of times without losing strength.

Steel—Best for dry environments since moisture will cause these washers to rust.

3 Wave—More points of contact than single-wave washers for a better grip.

	No. of Waves	ID	OD	Thk.	Overall Ht.	Pkg. Qty.		Pkg.
Steel



	3/8"	3	0.393"	0.500"	0.007"	0.070"	50	000000000	000000

Shims for Keyed Shafts

With a notch or tab, these shims fit snugly on keyed shafts to align and space gears, sprockets, and bearings. On keyed arbors, they’re often used to accurately space saw blades and cutters.

Notch

Fit these shims around keyed shafts and arbors that have a key inserted. They’re often referred to as arbor spacers.

18-8 Stainless Steel—The choice for wet and outdoor environments, these shims resist rust. However, they’ll corrode or pit when exposed to salt water and chemicals.

							Notch
	Thk.	Thk. Tolerance	ID	ID Tolerance	OD	OD Tolerance	Wd.	Dp.	Min. Hardness	Pkg. Qty.		Pkg.
18-8 Stainless Steel







				For 3/4" Diameter Shafts

				0.007"	-0.0007" to 0.0007"	3/4"	0" to 0.011"	1 1/8"	-0.002" to 0.002"	3/16"	5/64"	Rockwell B80	10	000000000	000000




						For 7/8" Diameter Shafts

						0.007"	-0.0007" to 0.0007"	7/8"	0" to 0.011"	1 3/8"	-0.002" to 0.002"	3/16"	5/64"	Rockwell B80	10	000000000	00000




								For 1" Diameter Shafts

								0.007"	-0.0007" to 0.0007"	1"	0" to 0.011"	1 1/2"	-0.002" to 0.002"	1/4"	3/32"	Rockwell B80	10	000000000	00000




										For 1 1/4" Diameter Shafts

										0.007"	-0.0007" to 0.0007"	1 1/4"	0" to 0.011"	1 3/4"	-0.002" to 0.002"	5/16"	1/8"	Rockwell B80	5	000000000	0000




												For 1 1/2" Diameter Shafts

												0.007"	-0.0007" to 0.0007"	1 1/2"	0" to 0.011"	2 1/8"	-0.002" to 0.002"	3/8"	5/32"	Rockwell B80	5	000000000	00000




														For 2" Diameter Shafts

														0.007"	-0.0007" to 0.0007"	2"	0" to 0.011"	2 3/4"	-0.002" to 0.002"	1/2"	3/16"	Rockwell B80	5	000000000	00000