These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

These carriages and guide rails are steel.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Adapt most 15 mm guide rails to fit on T-slotted assemblies.

Run many cycles in tight spaces before replacing or re-greasing carriages.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Use these carriages and guide rails in temperatures up to 300° F.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

Mate with a T-slotted rail to add linear motion to your assembly.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

Mount along a wall or other vertical surface.

Use these carriages and guide rails for light loads where precise movement is not required.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

V-shaped rollers and rails allow these carriages to operate well in dirty environments because the debris won't get trapped on the rail.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

These steel track rollers and guide rails support loads up to 300 lbs.

Good for use in pick-and-place applications, machine tool doors, and telescopic press arms, these rugged slides are designed to carry heavy loads.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

These slides fully extend for convenient access to the back of drawers.

The stacked design provides stability for deep and wide drawers.

A lever locks the drawer in the open as well as closed position; push the lever to release the lock.

With fewer moving parts than other lock-open drawer slides, these collect less debris for a longer service life.

The size of a finger, these tiny slides open in both directions. All have ball bearings for smooth operation.

A stop holds the drawer open; push firmly on the drawer to close.

When you don't have enough clearance for side-mount or under-the-counter slides, mount these to the base of your drawer.

A stop holds the drawer closed; pull firmly on the drawer to open.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

With 2" of each end softened, it's easier to machine a custom end for mounting. The rest of the shaft is case-hardened, which increases hardness and wear resistance on the surface of the shaft while allowing the center to remain soft for absorbing stresses caused by shifting loads.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.