Titanium Solvents | McMaster-Carr

Filter by

For Removing

Buffing and Polishing Compounds

Container Type

Container Size

Solution Type

Flash Point

For Use With

Performance

Form

U.S.–Mexico–Canada Agreement (USMCA) Qualifying

Yes

DFARS Specialty Metals

REACH

RoHS

Export Control Classification Number (ECCN)

Type

Application

Color

Clarity

Consistency

Viscosity

Certification

Military Specification

MIL-STD-792

Forward

How can we improve?

12 Products

No-Residue Solvent-Based Parts Washing Solutions

Unlike other solvent-based parts washing solutions, these won't leave anything behind. They have a mild odor.

Note: Use only at room temperature; do not heat.

153° F Flash Point—Solutions with 153° F flash point are known as high-flash-point solutions.

Cannot Be Sold To—These solutions cannot be sold to the areas listed because they exceed local regulatory limits on VOC (volatile organic compounds).

	Container
	Size, gal.	Type	Solution Type	For Use On	For Removing	Flash Point, ° F	Cannot Be Sold To		Each
Liquids



		5	Pail	Solvent Based	Aluminum, Brass, Bronze, Copper, Glass, Iron, Plastic, Stainless Steel, Steel, Titanium	Asphalt, Buffing and Polishing Compounds, Fingerprints, Grease, Lapping Compounds, Oil, Paint	105	California	1974N11	0000000


		5	Pail	Solvent Based	Aluminum, Brass, Bronze, Copper, Iron, Plastic, Stainless Steel, Steel, Titanium	Buffing and Polishing Compounds, Grease, Lapping Compounds, Oil	153	California	3457K15	000000

Solvent-Based Parts Washing Solutions

Leave a corrosion-resistant film on parts after washing. These solutions have a mild odor and contain no chlorinated solvents.

Note: Use only at room temperature; do not heat.

153° F Flash Point—Solutions with 153° F flash point are known as high-flash-point solutions.

Cannot Be Sold To—These solutions cannot be sold to the areas listed because they exceed local regulatory limits on VOC (volatile organic compounds).

	Container
	Size, gal.	Type	Solution Type	For Use On	For Removing	Flash Point, ° F	Cannot Be Sold To		Each
Liquids



		5	Pail	Solvent Based	Aluminum, Brass, Bronze, Copper, Iron, Plastic, Stainless Steel, Steel, Titanium	Buffing and Polishing Compounds, Grease, Lapping Compounds, Oil	105	California	3229K1	0000000


		5	Pail	Solvent Based	Aluminum, Brass, Bronze, Copper, Iron, Plastic, Stainless Steel, Steel, Titanium	Buffing and Polishing Compounds, Grease, Lapping Compounds, Oil	153	California	3457K11	000000
		50	Drum	Solvent Based	Aluminum, Brass, Bronze, Copper, Iron, Plastic, Stainless Steel, Steel, Titanium	Buffing and Polishing Compounds, Grease, Lapping Compounds, Oil	105	California	3229K3	00000000

Adhesive Primers for Film, Signs, and Labels


4 fl. oz. Container, Spray Bottle	32 fl. oz. Container, Spray Bottle

Spray these adhesive primers onto a mounting surface to quickly and smoothly apply signs, labels, and protective films. These primers float adhesive-backed sheets above a surface until you press them down, giving you time to position the sheet and remove any wrinkles. Since the sheet doesn’t stick right away, you can apply large sheets without needing a second pair of hands. These primers also work with non-adhesive films. Even in hot or cold temperatures, your sheet will stay put.

Clean the mounting surface with adhesive primer before applying a film, so no residue is trapped underneath. Use a smoothing tool (sold separately) to squeeze out air bubbles and excess fluid. Drying time depends on application—most decals and films will dry within 90 seconds, but 3D printer sheets should dry for 24 hours before printing.

Container
Size, fl. oz.	Type	Drying Time, sec.	Consistency	Viscosity	Color		Each



	4	Spray Bottle	90	Thin Liquid	Not Rated	Amber	3476N11	00000


	32	Spray Bottle	90	Thin Liquid	Not Rated	Amber	3476N12	00000

Smoothing Tools

		Each
Film and Label Smoothing Tool, 4" Wide Blade	3477N11	00000	00000

Etching Solution Neutralizers

Clean etching solution residue from etched surfaces to prevent corrosion and rust.

For Use On	Container Size, fl. oz.		Each
Aluminum, Copper, Black-Oxide Metal, Brass, Bronze, Iron, Stainless Steel, Steel, Titanium	16	8597T18	000000

Etching Solution

Direct electrical current from your etcher to the surface being marked. Apply this solution to your etching pad, then place the etcher over the stencil on your material. Most solutions require a neutralizer (sold separately) to clean the surface after marking to prevent corrosion or rust.

General Purpose Etching Solution—Mark on a wide range of metals with a single solution. To achieve deeper marks on metals such as aluminum, copper, and stainless steel, use a solution that is specific to that metal.

Noncorrosive General Purpose Etching Solution—Won’t leave behind any residue and poses no risk of corrosion or rust, even without a neutralizer. This solution is halogen-free, chloride-free, and meets MIL-STD 792E, which makes it safe for use in environments most sensitive to corrosion, such as nuclear plants and oil and gas refineries.

	Etching Solution					Etching Solution Neutralizers
	For Use On (Max. Etching Dp.)	Mil. Spec.	Container Size, fl. oz.		Each		Each
Etching Solution



		Titanium (0.01")	—	16	9564N112	000000	8597T18	000000


		General Purpose Etching Solution



				Aluminum (0.002") Black-Oxide Metal (0.002") Brass (0.002") Bronze (0.002") Copper (0.002") Iron (0.01") Stainless Steel (0.002") Steel (0.01") Titanium (0.002")	—	16	8597T16	00000	8597T18	00000


				Noncorrosive General Purpose Etching Solution



						Aluminum (0.002") Black-Oxide Metal (0.002") Brass (0.002") Bronze (0.002") Copper (0.002") Iron (0.002") Stainless Steel (0.002") Steel (0.002") Titanium (0.002")	MIL-STD-792	16	9564N111	00000	———	0

		Each
		1-19	20-Up
Film and Label Smoothing Tool, 4" Wide Blade	3477N11	00000	00000