McMaster-Carr logo
    Filter by
    System of Measurement
    Strand Type
    Pitch
    Specifications Met
    Chain Type
    Bore Type
    Shaft Type
    Overall Width
    Component
    Chain Standard
    Material
    Sprocket Type
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Industrial Info Compare
    Chain Pitch Type
    Chain Style
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    15 Products

    Sprockets

    Image of Product. Front orientation. Drive Sprockets. Sprockets, For Double Strand.

    For Double Strand

    Sprocket teeth mesh with your roller chain to smoothly transmit power. These U.S.-made sprockets have machined teeth for a more precise fit than flame-cut or punched teeth, allowing them to glide in and out of the chain to reduce wear and extend chain life.
    Steel—Steel is strong, but best for dry environments since moisture will cause it to rust.
    Plain Bore—Plain bore sprockets give you options—machine a custom bore, weld, or press-fit them in place. They're sized to the minimum shaft diameter listed and are machinable up to the maximum.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    OD,
    mm
    Bore
    Type
    For Shaft
    Dia.
    Each
    For Double Strand
     
    Steel
    06B-2ISO3/8"1242Plain
    		10 mm to 16 mm3571N101000000
    06B-2ISO3/8"1448Plain
    		10 mm to 18 mm3571N10300000
    06B-2ISO3/8"1551Plain
    		10 mm to 20 mm3571N10400000
    06B-2ISO3/8"1654Plain
    		12 mm to 20 mm3571N10500000
    06B-2ISO3/8"1757Plain
    		12 mm to 24 mm3571N10600000
    06B-2ISO3/8"1860Plain
    		12 mm to 25 mm3571N10700000
    06B-2ISO3/8"1963Plain
    		12 mm to 28 mm3571N10800000
    06B-2ISO3/8"2066Plain
    		12 mm to 30 mm3571N10900000
    06B-2ISO3/8"2169Plain
    		12 mm to 30 mm3571N11000000
    06B-2ISO3/8"2582Plain
    		12 mm to 40 mm3571N114000000
    06B-2ISO3/8"2788Plain
    		12 mm to 45 mm3571N116000000
    06B-2ISO3/8"3097Plain
    		12 mm to 52 mm3571N119000000
     

    Flat-Edge Roller Chain and Links

    Image of Product. Front orientation. Roller Chain and Links. Flat-Edge Roller Chain and Links, Chain.

    Chain

    Image of Product. Front orientation. Roller Chain and Links. Flat-Edge Roller Chain and Links, Connecting Links.

    Connecting Links

    Image of Product. Front orientation. Roller Chain and Links. Flat-Edge Roller Chain and Links, Adding-and-Connecting Links.

    Adding-and-Connecting

    Links

    Image of Attribute. Front orientation. Contains Annotated. Flat-Edge Roller Chain and Links.
    No more hang-ups thanks to the flat, oblong side plates that create a level surface to keep items moving along conveyor lines. Unlike standard roller chain, there are no divots to snag products. Pair this chain with sprockets to transmit power between rotating shafts.
    Lubrication is key to smooth operation and long chain life. Routinely apply oil by hand or install an oil dispenser for continuous lubrication.
    Steel—The go-to for roller chain, steel is strong and economical. While proper lubrication helps prevent rusting, it’s not as corrosion resistant as coated or stainless steel.
    Connecting Link—Use a single link to join both ends of your chain. Start by removing the spring clip or cotter pin from the link’s side plate. Then, slide the link pins into the mating rollers at each end of your chain and snap the clip back on. Also known as master links.
    Adding-and-Connecting Link—An all-in-one link for adding and connecting. It adds a half-pitch length at the roller end, allowing finer length adjustments than full-pitch links. The pin end connects to your chain. Remove the side plate to install. Also known as half links and offset links.
    Chain
    Connecting Links
    Adding-and-Connecting
    Links
    Roller
    Chain
    Trade
    No.
    Std.
    Pitch
    Roller
    Dia.
    Roller
    Wd.
    Working
    Load, lb.
    Per
    Ft.
    Each
    Each
    Single Pitch
     
    Steel
    06B-2ISO3/8"0.250"0.225"6506027K110000006027K1000006027K5000000
     
    back to top