McMaster-Carr logo
    Filter by
    System of Measurement
    Number of Teeth
    Strand Type
    Specifications Met
    Pitch
    Attribute Image
    Chain Type
    Bore Type
    Chain Standard
    Component
    Overall Width
    Shaft Type
    Width
    Hub Diameter
    Sprocket Type
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Industrial Info Compare
    Material
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Chain Style
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    9 Products

    Sprockets

    Image of Product. Front orientation. Drive Sprockets. Sprockets, For Double Strand.

    For Double Strand

    Sprocket teeth mesh with your roller chain to smoothly transmit power. These U.S.-made sprockets have machined teeth for a more precise fit than flame-cut or punched teeth, allowing them to glide in and out of the chain to reduce wear and extend chain life.
    Steel—Steel is strong, but best for dry environments since moisture will cause it to rust.
    Plain Bore—Plain bore sprockets give you options—machine a custom bore, weld, or press-fit them in place. They're sized to the minimum shaft diameter listed and are machinable up to the maximum.
    For
    Roller Chain
    Trade
    No.
    Std.
    Pitch
    No. of
    Teeth
    OD,
    mm
    Bore
    Type
    For Shaft
    Dia.
    Each
    For Double Strand
     
    Steel
    12B-2ISO3/4"15103Plain
    		16 mm to 45 mm3571N2090000000
    12B-2ISO3/4"17115Plain
    		20 mm to 54 mm3571N211000000
    12B-2ISO3/4"19127Plain
    		20 mm to 62 mm3571N213000000
     

    Roller Chain and Links

    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Chain.

    Chain

    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Connecting Links.

    Connecting Links

    Image of Product. Front orientation. Roller Chain and Links. Roller Chain and Links, Adding-and-Connecting Links.

    Adding-and-Connecting

    Links

    Image of Attribute. Front orientation. Contains Annotated.
    Pair this chain with sprockets to transmit power between rotating shafts. Like the chain on a bike, the side plates have a figure-eight shape that grips the sprockets without slipping.
    Lubrication is key to smooth operation and long chain life. Routinely apply oil by hand or install an oil dispenser for continuous lubrication.
    Steel—The go-to for roller chain, steel is strong and economical. While proper lubrication helps prevent rusting, it’s not as corrosion resistant as coated or stainless steel.
    Corrosion-Resistant-Coated Steel—Combines the strength of steel with the corrosion resistance of stainless steel. The coating has been tested to withstand 500 hours of salt spray, so it holds up well in wet and outdoor conditions.
    Connecting Link—Use a single link to join both ends of your chain. Start by removing the spring clip or cotter pin from the link’s side plate. Then, slide the link pins into the mating rollers at each end of your chain and snap the clip back on. Also known as master links.
    Adding-and-Connecting Link—An all-in-one link for adding and connecting. It adds a half-pitch length at the roller end, allowing finer length adjustments than full-pitch links. The pin end connects to your chain—except for trade number 25, which requires a separate connecting link. Remove the side plate to install. Also known as half links and offset links.
    Chain
    Connecting Links
    Adding-and-Connecting
    Links
    Roller
    Chain
    Trade
    No.
    Std.
    Pitch
    Roller
    Dia.
    Roller
    Wd.
    Working
    Load, lb.
    Per
    Ft.
    Each
    Each
    Double Strand
     
    Steel
    12B-2ISO3/4"0.475"0.460"2,6006027K310000006027K4000006027K8000000
     
    Corrosion-Resistant-Coated Steel
    12B-2ISO3/4"0.475"0.460"2,6001222N7000001222N971000001222N97300000
     
    back to top