Also known as pipe plug sockets, these sockets have a square shape that provides the best possible grip on square fasteners and prevents rounding.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Tightly grip nuts and bolts with hand-driven tools, leaving finishes unscratched.

These short sockets fit spaces where height clearance is limited.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet IEC 60900.

Grip the indentations around the outside of tri-groove fasteners.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

Turn the knob to adjust the jaws and fit a range of fastener sizes.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Extra-long bits allow access to hard-to-reach fasteners.

Pivot the head to access fasteners from an angle.

A magnet holds the fastener securely enough to drive self-tapping screws.

Extra length allows access to fasteners on long bolts.

The square shape provides the best possible grip on square fasteners and prevents rounding.

Pivot the head to access fasteners from an angle.

Pivot the head to access fasteners from an angle.

Tighten or loosen nuts and bolts without damaging the finish.

A magnet holds the fastener securely enough to drive self-tapping screws.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.

No need to pull the socket off the tool—push a button to release.

Turn sockets in the most confined spaces.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Rather than teeth, these wrenches use a series of rollers to engage the ratchet, enabling work in the tightest of spaces. Also known as silent ratchets, they don't make the traditional click sound when turned.

The 25° offset head provides clearance when reaching over obstructions.

Position the head anywhere along the handle.

Pivot the head for access to fasteners in tight spots.

Bend around obstructions to turn hard-to-reach fasteners.

Measure with an accuracy of ±7%.

Measure with an accuracy of ±2%.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

Trust the precision of your measurements—these wrenches are accurate to ±2%.

Trust the precision of your measurements—these wrenches are accurate to ±1%.

Pivot the head to access fasteners in tight spots.

No need to pull the socket off the tool—push a button to release.

Turn sockets from above when there's not room to swing a standard wrench handle.

Apply more torque than your wrench can deliver on its own. Use a multiplier with a torque wrench to ensure you do not exceed the maximum input torque.

Attach one of these adapters to a socket to turn it with an open-end or box wrench.

These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.

Push the square drive through the adapter to change size.

Made of aluminum-bronze, these extensions satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Insulated to protect against accidental contact with live electrical circuits, these extensions are tested to 1,000 volts to meet IEC 60900.

Lock your socket into the extension to prevent accidental disengagement.

Change a standard wrench handle into a ratcheting wrench.

Pivot the head to access fasteners from an angle.

Fit these adapters between your wrench and socket to enable finger tightening.

Use sockets with tools that accept hex shanks, such as impact drivers and power drills.

Convert from one square drive size to another.

Pivot the head to access fasteners from an angle.

Lock your socket into the extension to prevent accidental disengagement.

Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

These sockets are also known as pin-in-Torx bits.

Extra-long bits allow access to hard-to-reach fasteners.

Keep a convenient mix of hex, Torx, Phillips, and slotted bit sockets on hand.

Extra-long bits allow access to hard-to-reach fasteners.

Lock your socket into the extension to prevent accidental disengagement..