From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

This wire bounces back after bending. It’s often used to construct springs and wire rope.

Polished to either a brushed or mirror-like finish, this material is often used to fabricate decorative enclosures and industrial workstations.

Harder than our other 304 stainless steel, these thin sheets offer better wear resistance for use as a wrap, liner, or cover.

Compare the appearance choices of our 304 stainless steel with these convenient selector packs.

This material has tighter tolerances than standard 303 stainless steel.

Able to withstand repeated stress and wear, 301 stainless steel has the strength required for applications such as springs and fasteners.

Use 430 stainless steel in decorative and light structural applications, rather than outdoors or in extreme temperatures.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

This material machines faster with less wear on cutting tools than standard 316 stainless steel. It's also called Prodec and Project 70+.

Bend this wire and it will stay in place. It's widely used as tying and locking wire.

These selector packs contain one 1-3/4"×3"×1/16" thick piece of 316 stainless steel in the following finishes: brushed #4, mirror-like #8, and unpolished.

Because these thin sheets are harder than our other 316 stainless steel, they offer better wear resistance. Use them as a wrap, liner, or cover.

Stronger and more corrosion resistant than 316 stainless steel, Nitronic 50 is especially well-suited for use as shafts and fixtures in marine environments.

Each piece is precision ground to offer tighter tolerances than standard 17-4 PH stainless steel.

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

Also known as Project 70+, this material machines faster with less wear on cutting tools than standard 17-4 PH stainless steel.

Widely used to fabricate fasteners and engine components, A286 will maintain its strength as temperatures rise.

One of the most machinable types of stainless steel available, 416 contains sulfur for fast machining without clogging cutting tools. It's used for gears, screws, and shafts.

Precision ground to a tight diameter tolerance, these rods are all set for turning applications in a lathe.

Bend this wire and it will stay in place. It's commonly used as tying and locking wire.

Ready for turning in your lathe, these rods are precision ground to a tight tolerance.

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

Suitable for making molds, 420 stainless steel is a hard, wear-resistant material that can be finely polished to a very smooth surface.

This material is hardened for increased wear resistance over standard 420 stainless steel.

440A stainless steel resists damage from impact and abrasion. It's often used for cutlery and valve components.

309/310 stainless steel has high levels of chromium and nickel to provide good corrosion resistance at elevated temperatures. It's often used in heat exchangers and furnaces.

Use these general purpose shafts with bearings, sprockets, and gears to transmit rotary motion.

These shafts have keyways only on the ends, leaving a plain shaft in the center. Use the keyways with machine keys to transmit torque to gears, sprockets, and other keyed components. Use the middle of the shaft with bearings and other round-bore components.

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

18-8 stainless steel threaded rods have good chemical resistance.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Stronger and more wear resistant than 18-8 stainless steel, these threaded rods are mildly chemical resistant. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

Grade B8M threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

The most corrosion resistant stainless steel threaded rods we offer, these Alloy 20 stainless steel threaded rods contain nickel to withstand exposure to sulfuric, phosphoric, and nitric acids.

Also known as hood pins, these studs have a cotter pin lodged through a drilled hole in the unthreaded portion for light duty holding, such as securing access panels and locking other fasteners.

A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring.

316 stainless steel studs have excellent resistance to chemicals and salt water.

These coupling nuts have good chemical resistance.

More corrosion resistant than 18-8 stainless steel coupling nuts, these nuts have excellent resistance to chemicals and salt water.

Often called sleeve nuts, these thread adapters fasten parts with right-hand threads to parts with left-hand threads.

Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.

Found in hand-powered clamps, vises, grates, doors, and work tables, lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Multiple thread channels (also known as thread starts) create faster linear travel than ball screws with a single thread start.

Made of cadmium-plated steel, these externally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made of stainless steel, these externally threaded rod ends provide excellent corrosion resistance.

Along with internal threads, these rod ends have a double row of precision ball bearings that allows high speeds and smooth operation.

Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension. Add right- and left-hand threaded rod ends to build your linkages.

These rod end bolts are good for wet and corrosive environments—for maximum mounting flexibility, cut the fully threaded shaft to whatever length you need.

Made of stainless steel, these rod end bolts are stronger and more corrosion resistant than our standard flat-shoulder rod end bolts.

Made of zinc-plated steel or stainless steel, these clevis rod ends offer more corrosion resistance than standard steel clevis rod ends.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel ball joint linkages.

Stronger than plastic models, these stainless steel swivel joints are also more corrosion resistant than steel joints.

Typically used with low-pressure stainless steel threaded pipe fittings.

Typically used with medium- to high-pressure stainless steel threaded pipe fittings.

One end of these shafts is machined to fit into the mixer; the other is machined to fit into an attachment like a propeller.

The guide rods direct flow to the magnetic rods. They’re helpful in removing dry particles from fine powder and low-flow applications.

These filters are designed without guide rods to prevent wet and sticky material from blocking flow.

Pull the rods from their sleeve to release particles stuck to the filter.

Combine these setup studs with T-slot nuts, flanged nuts, setup clamps, or setup blocks to clamp and hold workpieces, vises, and other objects onto your fixturing table. Also known as double-ended studs, they have threads on both ends.