More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

These 18-8 stainless steel anchors have good chemical resistance.

These 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A hex head allows for a secure grip with a wrench.

Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.

18-8 stainless steel anchors have good chemical resistance.

These 410 stainless steel screws are more corrosion resistant than ultra-corrosion-resistant coated steel screws.

Drive these hangers into wood with an adjustable wrench, pliers, or a special driver bit.

18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.

Support strut channel at a right angle to the beam.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Route pipe, tubing, and conduit across strut channel.

Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Tighten the bolt for an exact fit around material. Clamps secure vertical pipes in sanitation drain applications and prevent them from coming in contact with the mounting surface.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Cut as much strap as you need to hang duct, pipe, and other materials.

A mounting plate provides a more secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Identify bundles at a glance with these ties that are coated for an additional level of corrosion resistance.

Use these mounts with stainless steel cable ties when working in corrosive environments.

Clamp around a pipe or tube to guide rope.

Also known as footman's loops, use these guides to prevent webbing from twisting, or as anchor points in tie-down applications.

Use these plates where full lengths of track won't fit to create one anchor point.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

These compression sleeves are designed to meet lifting specifications.

These thimbles are also known as thin pattern thimbles.

Smooth rounded edges and an endless design prevent snags.

Install these clevis-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Also known as socket-end swage fittings, install these eye-end fittings with a roller swage press for a strong, permanent hold.

Also known as socket-end swage fittings, install these stud-end fittings with a roller swage press for a strong, permanent hold.

Add a mounting-plate to wire rope without having to fray the rope or use a compression tool.

Add a stud end to wire rope without having to fray the rope or use a compression tool.

Compress the thin shank wall with a hand tool to attach these light duty stud-end fittings. They are also known as hand swage fittings.

Compress the thin shank wall with a hand tool to attach these light duty eye-end fittings. They are also known as hand swage fittings.

Also known as screw eyes, use the sharp point of these eyebolts to mount directly into wood.

Lock by screwing the latch into the body.

A lock slides upward over the latch to lock. The latch opens outward to accept large diameters of rope.

Mount this anchor to vertical and horizontal I-beams.

These stainless steel anchor studs offer excellent corrosion resistance.