These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Flip these wrenches over to ratchet in the opposite direction.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

Suitable for occasional maintenance work, these sets are imported.

These wrenches are made of stainless steel for excellent corrosion resistance.

When working in tight spaces, these short wrenches fit where others can't.

Suitable for occasional maintenance work, these sets are imported.

Suitable for occasional maintenance work, these sets are imported.

A lever reverses the ratchet direction.

A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.

These lightweight tools are also known as AN (Army-Navy) wrenches.

Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These are also known as tappet wrenches.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

When turning fasteners in small spaces, these short wrenches fit where others can't.

Also known as alligator wrenches and water-meter nut wrenches, the V-shaped head fits multiple hex fastener sizes.

Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.

One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.

Made of stainless steel, these wrenches have excellent corrosion resistance.

Fit the narrow head into tight spaces and around thin fasteners.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.

Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.

The handle is covered in plastic for a comfortable grip.

Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.

A plastic-covered handle provides a comfortable grip.

These tools have the heavy duty handle and adjustment mechanism of a pipe wrench and the smooth jaws of a traditional adjustable wrench.

Fit the thin head and long jaws into narrow spaces.

Also known as a basin wrench, this tool has a pivoting head and spring-close jaws for working in tight spaces where it’s difficult to adjust a traditional wrench.

Turn fasteners with the firm grip of a wrench and the adjustability of pliers.

Flip the wrench over to use the raised section on the head as a hammer.

A ratchet mechanism in the head allows you to turn fasteners in tight spaces without removing and repositioning the wrench.

The handles are covered in plastic for a comfortable grip.

These wrenches have one pivoting socket end and one open end.

Mount to walls, cabinets, and other steel surfaces.

Organize your tool drawer by positioning these low-profile rails to accommodate wrenches of any length.

Tabs hold wrenches in place.

Made of stainless steel, these wrenches have excellent corrosion resistance.

Open and close the jaws with one hand. Press the lever and slide the bottom jaw to the desired position; tension keeps it in place.

Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.

The jaws grip most round surfaces, even highly polished objects. Push down on the wrench and pull the handle toward you—the jaws will tighten around the workpiece.

Use one end as a traditional pipe wrench and the other to loosen valve wheels. These are also known as engineers’ pipe wrenches.

Turn the end of the handle to set torque, and the wrench makes an audible click when it reaches the setting.

Use your ratchet wrench as a handle to reach filters and other round objects in tight spots.

Also known as bung wrenches, these tools are used to install and remove screw-in drum plugs.

When the set torque is reached, these wrenches slip to disengage and stop overtightening.

In addition to standard and pop-up sink drains, these wrenches install and remove overflow outlets and toilet inlet connectors (also known as spuds).

The ball end allows angled entry to turn screws in hard-to-reach areas. Protect your stainless steel screws by using a stainless steel L-key. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of stainless steel keys, which protect stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Sets include an assortment of keys with a long shaft for more reach and a short shaft for more torque. Use stainless steel keys to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

Protect your stainless steel screws by using a stainless steel driver. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

Use these caps to hold components in place and protect shaft ends.

Also known as E-style rings.

Slide these rings into place with one twist—no tools required—for applications with high thrust loads.

No groove required—these rings have teeth that firmly grip the bore.