Extend your reach in hard-to-access areas—turn these valves on and off using a square ratchet to grasp the hole at the end of the handle. Use with water, oil, air, and inert gas.

These valves can handle at least twice the pressure of other compact valves. Install them in tight spots. Use with water, oil, air, and inert gas.

For installation in instrument panels, these valves have threads and a hex nut below the handle. They’re for use with water, oil, air, and inert gas.

These valves are rated for at least three times the pressure of standard threaded valves. Use with water, oil, air, inert gas, and steam.

Often used in high-purity applications, such as oxygen service, these valves come cleaned and bagged. Use with water, oil, inert gas, and steam.

Bolt these valves to ANSI flanges. They’re for use with water, oil, air, inert gas, and steam.

Threads and a hex nut below the handle allow you to install these valves in instrument panels. For extra gripping power and a strong seal, they have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, inert gas, and steam.

For extra gripping power and a strong seal, the Yor-Lok fittings on these valves have two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. These valves are for use with water, oil, air, and inert gas.

Often used for oxygen service and other high-purity applications, these valves come cleaned and bagged. Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. For easy maintenance, they have a three-piece bolted body that disassembles inline so you can access internal components without removing welded connections.

Weld these valves to unthreaded metal pipe for a permanent, flush connection that permits smooth flow through a line. Use with water, oil, inert gas, and steam.

The most chemical-resistant threaded valves we offer, these have a PTFE seal and an alloy body that can withstand extremely aggressive and corrosive chemicals, such as methyl ethyl ketone and toluene.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. All have a PTFE seal and a corrosion-resistant 316 stainless steel body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

3-A certified as meeting sanitary design standards, these valves control the flow of liquids in food, dairy, pharmaceutical, and cosmetic plants.

Protect personnel and equipment in the presence of diesel fuel, fuel oil, gasoline, and kerosene. Fire-tested to meet American Petroleum Institute (API) 607, Edition 4, these valves are designed to securely isolate fluid and prevent the spread of fire.

To create a tight seal in vacuum conditions higher than 29.9” Hg, these valves have ultra-high-vacuum tube fitting connections, which are also known as KF, QF, and NW fittings. They are often used in applications such as vacuum coating and heat treating, leak testing, and analyzing gases.

Also known as vacuum isolation valves, these block flow so you can install and remove gauges from your system. They can also be used to add or vent gases in high-vacuum systems.

These top-of-the-line valves are comparable to Asco Red Hat 8210G Series and Parker Gold Ring 23C Series.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

Less than half the size of our other compact valves, these have small pipe connections for miniature lines.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

Avoid pressure surges and system shocks that can damage piping by installing these valves that open and close slowly.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Often used to control single-acting, spring-return air cylinders, these valves have a third threaded port to exhaust media.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

Built to withstand the extreme cold of liquid nitrogen and liquid oxygen, these valves are cleaned and bagged for high-purity applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Install these valves in gas pipelines to automatically control the flow of natural gas, propane, and butane to equipment.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

Supply fuel oil to boilers, furnaces, and other equipment.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Also known as diaphragm valves, these have a diaphragm that can handle dirty liquid, slurries, and abrasive media without damage.

With a ball-valve design, these valves can handle three times the flow of butterfly valves.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

For three times the flow of butterfly valves, these have a ball valve design.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Designed to withstand the extreme cold of liquid argon, liquid carbon dioxide, and liquid nitrogen, these valves are cleaned and bagged to meet CGA G-4.1 standards for oxygen service. They gradually open and close to adjust and regulate flow.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a low-profile body and a narrow port-to-port length, these valves fit in tight spots. Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To withstand a maximum steam pressure of at least 4,800 psi @ 355° F in applications such as petroleum refineries, these valves are machined from a single piece of metal for seamless construction. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To maintain sanitary standards in food, beverage, and dairy systems that require frequent cleaning, these valves are made of FDA listed materials. Electropolished to a 20 Ra finish, they have smooth internal surfaces that prevent product buildup and inhibit bacteria growth. All have sanitary quick-clamp fittings for easy disassembly. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For a longer service life than other flanged flow-adjustment valves, these are designed to open and close with minimal wear on internal components. Use with water, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Also known as proportional solenoid valves, these adjust and regulate flow based on the intensity of the electrical signal into the valve.

For faster actuation than motor-driven valves, these operate on compressed air. Integrate them into PLC systems for automatic control over the valve position based on system conditions. The actuator has a built-in electric pilot valve that controls the air supply to the valve. Set how much to open the valve using the programmable controller on the actuator.

Threads and a hex nut below the handle let you install these valves through instrument panels. They are for use with water, oil, air, and inert gas. All divert flow between ports.

Bolt these valves to flanges to divert flow between ports in flanged pipelines. They’re for use with water, oil, air, and inert gas.

Designed to direct the flow of liquids in food, dairy, and chemical-processing facilities, these valves can be fully disassembled for clean-out-of-place (COP) processes.

Often installed on petroleum loading arms to test fuel quality without interrupting flow, these valves are fire-tested to meet American Petroleum Institute (API) 607, Edition 5, for securely isolating fluid and preventing the spread of fire.

These valves operate on electricity to automatically divert flow between ports. Use with water, oil, air, and inert gas.

Often used for chemical analysis and other laboratory testing, these valves have a PTFE seal and body to withstand aggressive and corrosive solutions. They operate on electricity to automatically divert flow between ports.

For food and beverage systems that require frequent cleaning, these valves have sanitary quick-clamp connections for easy disassembly. They operate on compressed air to automatically divert flow between ports more quickly than motor-driven valves. You must control the air to the actuator using either an electric pilot valve or a manual on/off valve.