Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Unlike the smooth and flat edges of standard fixture clamps, these clamps have ridges that bite into parts, making them good for gripping castings and rough-cut stock.

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

Use with T-slot nuts or bolts and a support to secure a workpiece, vise, or fixture to a machine table.

The stepped end provides support and quick height adjustment when paired with a step block.

Get everything needed for basic workholding on a machine table.

The offset shape provides more clearance above the nut than standard clamps. Also known as gooseneck clamps.

Position these clamps between two workpieces, vises, or fixtures and secure both to your machine table using T-slot nuts or bolts.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

An alternative to setup clamps, these heavy duty clamps have high holding power to secure workpieces during machining.

The handle locks in a horizontal position for more clearance above the clamp than standard hold-down toggle clamps.

Hold workpieces of different thicknesses without adjustment.

Push the lever to lock the handle and prevent accidental opening.

A nonreflective black oxide finish prevents glare that can interfere with machine vision systems.

Hold workpieces of slightly different thicknesses with one clamp. These clamps automatically adjust to compensate for imperfections or small inconsistencies on the material’s surface.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Weld these clamps to the side of an object or drill your own holes in the mounting plate and bolt into place.

Two sets of mounting holes allow mounting on the bottom or side.

The handle locks in a horizontal position for more clearance above the clamp.

These clamps have mounting holes on the bottom.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Push or pull the plunger to hold your workpiece from the side.

Pull the handle backward to push the plunger forward. These clamps secure when the plunger is fully extended to hold your workpiece from the side.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

Hold workpieces of different thicknesses without adjustment.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Push the lever to lock the handle and prevent accidental opening.

The plunger can be locked at any position along its travel.

The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces.

Hold workpieces at a 90° angle.

Each arm has a handle for turning the magnets on and off.

Hold magnetic workpieces in place with these clamps.

Clamp workpieces from the outside at a 90° angle, leaving the inside free for welding or fabrication.

The clamping arm slides freely along the bar for quick, one handed positioning. Tighten the screw onto a workpiece and the arm locks in place.

These clamps have twice the capacity of standard fast-action bar clamps.

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Hold up to five times the capacity of standard bar clamps. These are also known as I-beam clamps.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol-grip handle to lock the clamp in place.

Press the trigger to slide the clamping arm along the bar. Release the trigger and squeeze the pistol‐grip handle to lock the clamp in place.

Two swivel pads on each jaw pivot to grip nearly any shape of material.

Add components such as clamps, brackets, stops, rests, mounting plates, fixturing squares, risers, and V-blocks to build fixtures for welding and assembly.