Use these corrosion-resistant fittings in a low-pressure pipe line.

The male threads on these fittings have a sealant applied for extra leak protection.

Use these fittings in extreme-pressure conditions up to 15,000 psi.

When space is at a premium choose these compact fittings.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Press these fittings onto stainless steel pipe using a crimping tool for a permanent, leak-tight connection that's faster than threading or welding and doesn't require heat.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

With thicker, stronger walls than our standard-wall butt-weld pipe fittings, these fittings stand up to your high strength applications.

Use these fittings for low-pressure applications in noncorrosive environments.

Suitable for use in fire-protection applications, these pipe fittings are made of cast iron, so they are brittle and can be quickly opened with the strike of a sledge hammer.

The male threads on these fittings have a sealant applied for extra leak protection.

A galvanized finish gives these fittings better corrosion resistance than our plain steel high-pressure fittings. Also known as Pressure Class 3000 fittings.

Made to tighter tolerances than other steel pipe fittings, these are also known as instrumentation fittings.

For use in noncorrosive environments, these fittings have better strength than our low-pressure iron and steel pipe fittings.

The grooved ends on these iron fittings connect to pipe with a clamp to easily install piping systems.

These brass fittings have the strength to handle high-pressure applications.

Use these heavy-duty brass fittings for high-pressure drinking water applications.

Install and remove these high-pressure brass fittings with a socket wrench or hex key (sold separately).

Use these fittings in low-pressure flow applications. They have good corrosion resistance.

Less than an inch in length, these miniature fittings work well in low-pressure pipe lines that are tight on space.

Extreme pressures are no problem for these heavy-duty brass fittings.

Plated with nickel, these brass fittings resist rust better than steel and unfinished brass fittings. Select them when you need more strength in corrosive environments to handle higher pressures than our low-pressure fittings.

Also known as Schedule 40 fittings, these have thicker walls than our thin-wall aluminum unthreaded pipe fittings.

Socket-connect fittings are easier to weld than butt-weld fittings because the fitting doesn't need to align perfectly to the pipe. Slip the pipe into the socket and weld.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Also known as Pressure Class 3000 fittings, these have the highest pressure rating of all the aluminum pipe fittings we offer.

Also known as Pressure Class 200 fittings.

Connect these fittings to Schedule 40 plastic pipe—they are the industry standard for residential and commercial low-pressure plumbing and water supply applications. They are plastic for good corrosion resistance.

Connect these fittings to Schedule 80 pipe. With thicker, stronger walls than standard-wall fittings, they can handle heavy duty supply applications, such as water processing, wastewater treatment, and irrigation.

Use for pressures up to 60 psi. Also known as insert fittings, these slide into semi-flexible plastic pipe and secure with a clamp.

Made of polypropylene, these fittings won’t deteriorate when exposed to the damaging effects of ultraviolet light and are suitable to use outdoors. They have the chemical resistance to withstand acids, solvents, and other harsh substances.

These PVDF fittings meet UL 94 V-0 for flame retardance, so they delay the spread of flames to valuable equipment. PVDF is comparable to Kynar, and has the chemical resistance to stand up to solvents and other harsh substances.

Also known as Victaulic fittings, these have grooved ends that connect to pipe with a clamp, so you can access your chemical process line for routine maintenance. Fittings have excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances.

These fittings have excellent corrosion resistance to handle a wide range of acids and other highly-corrosive chemicals. They are commonly used in metal surface treating applications, plating solution lines, and other chemical process applications. Reinforced with layers of fiberglass, they have better strength and durability than any of our other pipe fittings for chemicals.

The inside of these fittings won’t leach contaminants into your line or accumulate particles—they’re polished to an ultra-smooth 12 Ra finish, which also makes them easy to clean. Made of polypropylene, they resist organic solvents, acids, and alkalis better than CPVC fittings.

Bolt two same-size flanges together with a gasket to create an access point within a line. Flanges are an economical option for gravity-flow chemical waste systems. They are ABS plastic, which has excellent strength and impact resistance and good chemical resistance.

These Schedule 40 fittings are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

With thinner walls than Schedule 40 fittings, these are lighter in weight and have more space on the inside for high-flow applications, such as underground gravity-flow sewer and storm drainage lines. They are also known as SDR 35 fittings.

Made of corrosion-resistant plastic, these fittings won’t deteriorate when used in oil applications. They have high strength and impact resistance.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Use at pressures up to 4,300 psi.

The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

For applications that require an extra level of cleanliness, these fittings are individually bagged to prevent contamination.

The male pipe threads on these fittings have a sealant applied for extra protection against leaks.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket between them. The flanges’ sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than other high-vacuum fittings with rubber gaskets.

The flat face of the fitting connects to a tube adapter so you can slide the tubing and fitting sideways to disconnect in cramped spaces. They are also known zero-clearance fittings.

Solder these fittings to tubing for a permanent, leak-tight connection. They are also known as sweat fittings.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

Also known as JIC (Joint Industrial Council) fittings, these connect to tubing that is flared to 37°. They can handle higher pressures than 45° flared fittings.

With a nickel-plated finish, these compression fittings resist corrosion better than plain brass fittings.

The sleeve in these fittings is rubber instead of metal, so it cushions the tubing and absorbs vibration while creating a tight seal.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Choose these metal fittings when you need better durability than our plastic push-to-connect fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Use these fittings in an air vacuum system to avoid the hassle of brazing and welding. Insert two fittings into a clamp and tighten to form a secure seal in steel tubing.

Thicker walls make these fittings—sometimes called flareless or bite fittings—withstand about twice as much pressure as standard compression fittings, so they’re good for hydraulic power applications.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

These Monel fittings have the corrosion resistance to handle hydrofluoric and sulfuric acid. Also known as instrumentation fittings, they include a nut with two sleeves.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight seal on tubing that is flared to 37°.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

A built-in shut-off valve stops airflow when the fittings are disconnected from tubing.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Connect high-pressure brake lines with fittings that won’t crack in frigid temperatures. Often used on commercial trucks and trailers, these fittings meet Department of Transportation FMVSS 571 safety standards.

Withstanding up to 300° F, these fittings have the highest temperature rating of all our brass push-to-connect tube fittings for air and water.

Designed for use in welding applications, these fittings are flame retardant.

Barbs grip onto tubing.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

The nickel plating on these fittings provides better corrosion resistance than unplated brass fittings.

A single sleeve (ferrule) compresses the tubing as you tighten the nut on these fittings, creating a strong seal. They are brass for good corrosion resistance.

Safe for use in your air brake line, these fittings meet Department of Transportation FMVSS 571 standards. They’ve been tested for thermal cycling, vibration, and burst pressure, so put them to work right away.

Made of acetal, these compression fittings are lighter in weight than metal compression fittings and won’t absorb moisture when used in wet environments.