Use these corrosion-resistant fittings in a low-pressure pipe line.

Also known as Code 61 SAE hydraulic flanges.

These fittings are made to tighter tolerances than other stainless steel pipe fittings. They are also known as instrumentation fittings.

Choose these fittings when you want the same high-quality found in our low-pressure pipe fittings, but need more strength to handle higher pressures.

Use these fittings for low-pressure applications in noncorrosive environments.

Assortments contain threaded pipe in various lengths.

These flanges are for low-pressure applications in noncorrosive environments.

The galvanized finish on these fittings provides fair corrosion resistance. Fittings are for use in low-pressure applications.

A plastic sleeve prevents destructive corrosion when connecting different metals.

The male threads on these fittings have a sealant applied for extra leak protection.

These fittings can stand up to high-pressure applications. Use them in noncorrosive environments.

Also known as Pressure Class 1500 steel flanges, these have the strength to handle high pressures.

Combine an adapter with a two-piece pipe flange (sold separately) to build a customized flange connection for noncorrosive environments.

For use in noncorrosive environments, these fittings have better strength than our low-pressure iron and steel pipe fittings.

With better strength than our low-pressure steel flanges, these are for use in medium-pressure applications.

Typically used with medium-pressure galvanized iron and steel threaded pipe fittings. Also known as Schedule 80.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

The strongest steel fittings we offer, these can withstand extreme-pressure applications.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Typically used with standard-wall and low-pressure iron and steel unthreaded pipe fittings. Also known as Schedule 40.

Access the inside of lines operating up to 285 psi, so you can vent pressure, drain liquid, or take samples. Made of black-coated steel, these bleed rings should be used in dry environments to prevent rusting.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Also known as Code 61 SAE hydraulic flanges.

Tap into your line in systems operating up to 1,400 psi to vent pressure, drain liquid, or take samples. Made of black-coated steel, these bleed rings should be used in dry environments to prevent rusting.

Typically used with extreme-pressure iron and steel unthreaded pipe fittings. Pipe is also known as Schedule XXH .

These brass fittings have the strength to handle high-pressure applications.

Typically used with high-pressure brass and bronze threaded pipe fittings.

Use these fittings in low-pressure flow applications. They have good corrosion resistance.

Used in low-pressure pipe lines, these brass fittings have a plating that makes them shiny and improves corrosion resistance.

Plated with nickel, these brass fittings resist rust better than steel and unfinished brass fittings. Select them when you need more strength in corrosive environments to handle higher pressures than our low-pressure fittings.

In addition to being lightweight, these aluminum fittings offer good corrosion resistance. Use them in low-pressure flow applications.

Connect these fittings to thick-wall plastic pipe—they have thicker, stronger walls than standard-wall fittings, so they can handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation. They can withstand pressures up to 900 psi.

Use these clamps to connect easy-access CPVC pipe fittings and pipe.

Also known as no-hub couplings, these have a one-piece sleeve with a stop in the center, so you know your pipe is always aligned correctly.

A turn of the T-handle will tighten and loosen these connectors, so you can quickly disassemble and reassemble your lines without tools.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Joints are for one-way flow and are meant to be used in pairs—one joint serves as the supply line while the other serves as the return line.

Use in low-pressure applications up to 150 psi.

Stop leaks where a fitting and a pipe join without turning off your line.

No sleeve is required to assemble these fittings, which makes for a faster, more convenient installation compared to 37° flared fittings. They are also known as refrigeration and SAE fittings.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Individually bagged to prevent contamination, these fittings are suitable for applications that require a high level of cleanliness.

A single sleeve (ferrule) bites into tubing as you tighten the nut, creating a strong seal. The nut and sleeve are included.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

Also known as JIS (Japanese Industrial Standard) fittings.

Thicker walls make these fittings—sometimes called flareless or bite fittings—withstand about twice as much pressure as standard compression fittings, so they’re good for hydraulic power applications.

These fittings have two sleeves for extra gripping power. They bite into steel tubing as you tighten the nut to form a strong seal.

Make lightweight connections without the hassle of matching the exact thread type—these fittings connect to NPT, NPTF, BSPP, BSPT, and other universal threads.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Made of brass, these fittings have good corrosion resistance.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Use at pressures up to 250 psi.

Withstanding temperatures up to 300° F, these fittings have the highest temperature rating of all our push-to-connect tube fittings for air and water.

Ball bearings allow these fittings to rotate 360°, even after they are tightened. They have a special seal that reduces friction to allow for continuous rotation.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Monitor flow with these clear fittings.

The nickel plating on these fittings provides better corrosion resistance than unplated brass fittings.

Color-code fittings for easy identification. These aluminum fittings have good corrosion resistance, but are lighter in weight than brass.

You don't need a clamp to secure these fittings to tubing. They have a nut on the barbed end that tightens to holds the tubing in place.

These fittings include a nut with a built-in sleeve (ferrule), so there’s no need to remove the nut for assembly.

Couplings can handle pressures up to 250 psi.

These brass couplings have good corrosion resistance.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Made of stainless steel, these fittings are more durable than plastic barbed tube fittings for food and beverage.

Made of FDA listed materials, these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

Also known as instant fittings, they connect to tubing with a push, and an internal gripping ring and O-ring hold the tubing tight. Use in applications up to 150 psi.