Spray to fill in small dents, cracks, and scratches. These surface fillers build on themselves to cover minor surface imperfections.

Make castings and fill voids with these two-part pourable epoxies.

Press these putty surface fillers in place to fill in holes, cracks, and dents. When exposed to sunlight or a UV lamp, they begin to harden immediately.

Mix these two-part epoxy surface fillers to create a strong repair in wet environments or underwater.

Able to withstand temperatures up to 2300° F, these ceramic surface fillers are often used as thermal insulation on brick, mortar, burner blocks, furnace holders, and thermocouples.

Also known as sloshing compounds, these surface fillers bond to rough, rusty surfaces in fuel tanks to repair leaks and prevent further corrosion.

Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F.

For use in processing equipment that carries large particles 1/16" in diameter and larger, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as pump housings, chute linings, and hoppers.

Chemicals will not affect these two-part epoxies. They repair cracked, worn, and damaged surfaces.

Stop leaks in metal tanks and equipment without draining the contents.

Stop leaks in metal tanks and equipment without draining the contents. Until a permanent repair can be made, rub these sticks into the leak to form a temporary seal.

Seal leaks around small holes.

Spray these surface fillers on molded plastic parts that have surface blemishes, scratches, and mold lines. Use with ABS, polystyrene, and glass-filled nylon.

Repair worn and torn rubber parts. These two-part fillers are self leveling and form a tough, flexible new surface. They're often used with conveyor belts, mill liners, and pumps.

Fill cracks in horizontal, vertical, and overhead concrete surfaces.

Fill cracks up to 4" deep on horizontal surfaces, such as floors and sidewalks.

Stop active leaks of up to 50 gallons per minute in concrete, brick, and stone. These crack fillers begin to harden within seconds to create a permanent fix that won't shrink.

Not only do these leveling compounds withstand severe abrasion, wear, and impact, they also stand up to steel wheels and heavy blows without cracking.

Patch concrete floors, stairs, and walls with these compounds.

Use these two-part compounds to patch concrete floors, stairs, and walls in cold environments, such as freezers. At room temperature, they cure faster than any of our other concrete patching compounds.

For use when thickness will be less than 2", sand mixes consist of cement and sand.

Also known as mortar hoes, the blade on these tools has holes to allow concrete to pass through as you mix.

Make removing form-board stakes easier.

Create grooves in poured concrete slabs to control cracking caused by drying, settling, and freezing.

Use floats after edging and grooving to smooth the surface and allow trapped air and water to escape.

Drag these brooms along hardening concrete to create a rough surface for traction in slippery environments.

Keep drywall compound close at hand so you can apply it over seams quickly and efficiently.

Also known as mud pans, use these to mix small amounts of drywall compound or to bring it to your work area.

Cut perfect circles up to 16" in diameter to create openings for pipes, conduit, or lighting fixtures.

Smooth joint compound on both sides of an interior corner with these trowels.

Remove hardened flecks of mortar, dirt, and other debris.

Smooth and spread grout between tiles.

These long, thin brushes have semi-soft bristles to smooth out wrinkles and air bubbles after wall coverings are applied without damaging the wall covering itself.

Fix damaged wood or build up and replace missing wood.

Fill and conceal small cracks, nail holes, and blemishes. Compounds are ready to use.

Fix cracks in drywall and stop them from spreading. Place the included fabric over wall cracks and cover with the acrylic paste. This results in a flexible, nonshrinking repair that prevents cracks from reappearing as the building continues to settle.

Spray these compounds onto ceilings to create a popcorn texture that covers stains, patches, and chips. The nozzle is upright for easy application.

Also known as drywall mud, these joint compounds are ready to use. Apply with drywall tape over seams for a finished appearance.

Spray these compounds onto drywall to create an orange-peel texture that covers stains, patches, and chips. The nozzle adjusts from a light to heavy spray.

Repair holes and seal gaps in roofing and gutters. These patching compounds are durable and water resistant.

Make a temporary repair to cracks in any flat roof. These patching compounds are a powder that forms a thick gel in minutes when poured directly into standing water and rain.

Reinforce hot- and cold-applied asphalt patching compounds and coatings with this flexible fabric.

Used on ceramic, concrete, and stone floor and wall tiles, grout consists of fine sand, masonry cement, and coloring.

Make flexible, waterproof repairs to rips and tears in canvas, leather, and acrylic fabric.

These crack fillers come in an easy-to-pour jug for filling cracks in asphalt up to 1/2” wide.

Hand-mold this putty to fill small openings in fire-resistant walls and floors.

Seal small openings in fire-resistant walls and floors.

Also known as block filler, these primers fill cracks and smooth surface irregularities. Use them to prepare concrete floors to extend the life of paint and coatings.