A wide tip provides more gripping power than standard swivel-tip set screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

A low-profile flat-faced ball tip allows these metric set screw to be used in low-clearance applications.

Stainless steel set screws have excellent corrosion resistance in most environments.

For maximum contact with angled and uneven surfaces, the tip swivels in all directions. The tip is narrow so it will fit through threaded holes.

Also known as tank-strap bolts, these T-bolts are commonly used with a band clamp or a strap to hold fuel tanks and other objects in place.

Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.

Choose these hoist rings when you need to lift your load from the side.

Also known as machinery eyebolts.

Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.

The matte black-oxide finish won't reflect light, allowing the eyebolts to blend into the background.

Also known as nut eyebolts, these are designed for through-hole applications.

Also known as screw eyes, use the sharp point of these eyebolts to mount directly into wood.

Use these to adjust the position of a fitting or an object under load and minimize twisting and knotting.

The snap and split ring swing freely and pull from the center for easy alignment.

These have split rings that swing freely and pull from the center for easy alignment.

For easy positioning before a load is applied, these rotate to minimize twisting and knotting of rope and chain.

Use these to adjust the position of a fitting or an object under load and minimize twisting and knotting.

Also known as rod‐end bearings, ball joint rod ends have an eyelet and a ball that swivels to support angular misalignment.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

An oil-embedded bronze insert slowly releases lubricant throughout the life of the rod end.

Connect your grease gun to the fitting to lubricate.

An oil-embedded bronze insert slowly releases lubricant to the rod end. Connect your grease gun to the fitting to relubricate.

Made to extremely tight tolerances, these externally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

With at least 55° of ball swivel, these rod ends accommodate greater misalignment than any other internally threaded rod end we offer.

Made of cadmium-plated steel, these internally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made of stainless steel, these externally threaded rod ends provide excellent corrosion resistance.

These anodized aluminum rod ends are lighter than stainless steel rod ends and have good corrosion resistance. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

Made of impact-resistant nylon, these externally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

An innovative body design keeps the ball from being pushed out when supporting thrust loads.

These externally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

Along with internal threads, these rod ends have a double row of precision ball bearings that allows high speeds and smooth operation.

Use these externally threaded linkages to create inline pivoting connections.

These linkages offer excellent wear resistance. They consist of internally threaded ball joint rod ends with a ball stud attached to simplify mounting.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

Along with excellent wear resistance, these linkages have a grease fitting for easy lubrication. An internally threaded rod end connects to threaded rods, studs, and other parts with male threads.

An oil-embedded bronze insert slowly releases lubricant throughout the life of the joint.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel and zinc ball joint linkages.

Made of stainless steel, these ball joint linkages offer more corrosion resistance than steel ball joint linkages.

Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made of 303/304 stainless steel, these mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Nickel-plated steel has some corrosion resistance.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Bolt these mounts down to keep your equipment stationary.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.

A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.

Higher deflection ratings translate to greater vibration and shock isolation.

Replace worn screws or customize your clamps.