Rotating for easy positioning before a load is applied, these minimize twisting and knotting of rope and chain.

These rotate for easy positioning before a load is applied to minimize twisting and knotting of rope and chain.

Adjust the position of a fitting or an object under load and minimize twisting and knotting.

The snap and split ring swing freely and pull from the center for easy alignment.

Minimize twisting and knotting of rope and chain and adjust the position of a fitting or an object under load.

Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.

The fixed base provides added stability and allows you to lift heavy loads with smaller thread sizes.

Choose these hoist rings when you need to lift your load from the side.

These snaps have an eye that rotates for easy positioning.

Lock the bolt with wire or a cable tie for a secure connection.

These rotate for easy positioning before a load is applied.

A ball-bearing swivel allows these to rotate under load. Attach to chain by inserting the included pin through a link.

These hooks swivel under load. They have a latch locks closed when a load is applied for a more secure connection than standard hooks.

Attach a rope to the ring on the pin for remote release where access in limited. These shackes have a clevis end for making pivoting connections.

Add a mounting-plate to wire rope without having to fray the rope or use a compression tool.

The swivel fork allows the lanyard to rotate freely.

Connect these fittings to air tools for pneumatic applications.

Fittings are metal for better durability than plastic barbed hose fittings. They have sharper barbs than standard barbed hose fittings to grip push-on hose without the need for clamps or ferrules. The more you pull on the fittings, the tighter the hose will grip.

Made of polypropylene, these fittings are lighter in weight than metal barbed hose fittings.

The industry standard for quick-disconnect couplings, these are also known as industrial interchange couplings. Compatible with Industrial-shape plugs and sockets.

Also known as live swivels, these fittings swivel continuously 360° before and after installation. This not only makes installation easier, but also eliminates the twisting and kinking that can cause hose failure. Fittings are threaded on both ends so you can connect them directly to a threaded hose or to pumps, cylinders, and other equipment in your hydraulic system. Use in high-pressure applications up to 5,000 psi.

These two-piece fittings screw directly onto the hose without the need for a separate adapter. When assembled, the fitting compresses against the hose, forming a strong seal. Also known as reusable fittings, they can be unscrewed from the hose end and used on a new hose. Use in high-pressure hydraulic applications up to 5,800 psi.

Fittings meet NSF/ANSI Standard 61 for drinking water. Attach them to garden hose for a variety of water supply applications. They are metal for better durability than plastic garden hose fittings.

The pin lugs on these fittings allow for easy gripping, so you can quickly connect to fire hydrants and washdown equipment. They swivel until tightened for easier installation than other fire hose fittings.

Use these two-piece fittings in grease and lubrication lines. They screw directly onto hose without the need for a separate adapter. When assembled, the fitting compresses against the hose, forming a strong seal. Also known as reusable fittings, they can be unscrewed from the hose end and used on a new hose.

Connect these swivels to the threaded end of your dispensing hose. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.

Joints are for one-way flow and are stainless steel for excellent resistance to corrosion caused by fluid flowing through them.

Joints are for one-way flow and are meant to be used in pairs—one joint serves as the supply line while the other serves as the return line.

Joints are for one-way flow and are brass for good corrosion resistance.

Joints are for two-way flow and are stainless steel for excellent resistance to corrosion caused by fluid flowing through them.

These fittings are strong enough to handle extreme pressures, yet small enough to fit into cramped spaces.

For use in noncorrosive environments, these fittings have better strength than our low-pressure iron and steel pipe fittings.

Use these heavy duty, corrosion-resistant fittings in high-pressure flow applications.

Extreme pressures are no problem for these heavy-duty brass fittings.

The plating on these brass fittings creates a shiny finish and provides extra protection in corrosive environments. Fittings have the strength to handle high-pressure applications.

Made of polypropylene, these fittings won’t deteriorate when exposed to the damaging effects of ultraviolet light and are suitable to use outdoors. They have the chemical resistance to withstand acids, solvents, and other harsh substances.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Made of nickel-plated brass, these tube fittings resist corrosion better than plain brass fittings. The male threaded ends connect to NPT, NPTF, BSPP, BSPT, and other universal threads, so you don’t have to bother matching exact thread types.

A 316 stainless steel body gives these fittings the best corrosion resistance of all our metal push-to-connect tube fittings.

Ball bearings allow these fittings to rotate 360°, even after they are tightened. They have a special seal that reduces friction to allow for continuous rotation.

The threads on these fittings mate with NPT, NPTF, BSPT, and BSPP threads.

Use at pressures up to 150 psi.

Barbs grip onto tubing.

Fittings have good corrosion resistance.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on stainless steel tubing that is flared to 37°.

The threads on the tube end of these fittings are Class 3A or 3B and adhere to tighter tolerances than other 37° flared fittings.

Also known as JIC (Joint Industrial Council) fittings, these provide a tight metal-to-metal seal on steel tubing that is flared to 37°.

A tube adapter sits flush against the flat face of the fitting so you can slide the steel tubing and fitting sideways to disconnect in cramped spaces. Also known as zero-clearance fittings.

Also known as rod‐end bearings, ball joint rod ends have an eyelet and a ball that swivels to support angular misalignment.

A PTFE-embedded insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

Connect your grease gun to the fitting to lubricate.

An oil-embedded bronze insert slowly releases lubricant throughout the life of these internally threaded rod ends.

These internally threaded rod ends have an oil-embedded bronze insert that slowly releases lubricant over time. Connect your grease gun to the fitting to relubricate.